參數資料
型號： MBM29PL160BD-90
廠商： Fujitsu Limited
英文描述： 16M (2M x 8/1M x 16) BIT
中文描述： 16米（2米x 8/1M × 16）位
文件頁數： 15/51頁
文件大?。?/td> 591K
代理商： MBM29PL160BD-90
15
MBM29PL160TD
-75/-90
/MBM29PL160BD
-75/-90
SPA : Sector Address to be protected. Set sector address (SA) and (A
6
, A
1
, A
0
) = (0, 1, 0).
SD : Sector protection verify data. Output 01H at protected sector addresses and output 00H at unprotected sector
addresses.
*1
.
*2
.
*3
.
This command is valid while fast mode.
Addresses from system set to A
0
to A
6
. The other addresses are “Don’t care”.
The data" 00H" is also acceptable.
Command Definitions
Device operations are selected by writing specific address and data sequences into the command register.
Writing incorrect address and data values or writing them in an improper sequence will reset the device to the
read mode. Table 7 defines the valid register command sequences. Note that the Erase Suspend (B0H) and
Erase Resume (30H) commands are valid only while the Sector Erase operation is in progress. Moreover both
Read/Reset commands are functionally equivalent, resetting the device to the read mode. Please note that
commands are always written at DQ
0
to DQ
7
and DQ
8
to DQ
15
bits are ignored.
Read/Reset Command
In order to return from Autoselect mode or Exceeded Timing Limits (DQ
5
= 1) to read mode, the read/reset
operation is initiated by writing the Read/Reset command sequence into the command register. Microprocessor
read cycles retrieve array data from the memory. The device remains enabled for reads until the command
register contents are altered.
The device will automatically power-up in the Read/Reset state. In this case, a command sequence is not required
to read data. Standard microprocessor read cycles will retrieve array data. This default value ensures that no
spurious alteration of the memory contents occurs during the power transition. Refer to the AC Read
Characteristics and Waveforms for specific timing parameters. (See Figure 5.1 and 5.2.)
Autoselect Command
Flash memories are intended for use in applications where the local CPU alters memory contents. As such,
manufactures and device codes must be accessible while the device resides in the target system. PROM
programmers typically access the signature codes by raising A
9
to a high voltage. However, multiplexing high
voltage onto the address lines is not generally desired system design practice.
The device contains an Autoselect command operation to supplement traditional PROM programming
methodology. The operation is initiated by writing the Autoselect command sequence into the command register.
Following the last command write, a read cycle from address XX00H retrieves the manufacture code of 04H. A
read cycle from address XX01H for
×
16 (XX02H for
×
8) retrieves the device code (MBM29PL160TD = 27H and
Table 8 MBM29PL160TD/BD Extended Command Definitions
Command
Sequence
Bus
Write
Cycles
Req'd
First Bus
Write Cycle
Second Bus
Write Cycle
Third Bus
Write Cycle
Fourth Bus
Read Cycle
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Set to Fast
Mode
Word
3
555H
AAH
2AAH
55H
555H
20H
—
—
Byte
AAAH
555H
AAAH
Fast Program *1
Word
2
XXXH
A0H
PA
PD
—
—
—
—
Byte
XXXH
Reset from Fast
Mode *1
Word
2
XXXH
90H
XXXH
F0H *3
—
—
—
—
Byte
XXXH
XXXH
Query
Command *2
Word
2
55H
98H
—
—
—
—
—
—
Byte
AAH
相關PDF資料
PDF描述
MBM29PL160BD-90PF 16M (2M x 8/1M x 16) BIT
MBM29PL160BD-90PFTN 16M (2M x 8/1M x 16) BIT
MBM29PL160BD-90PFTR 16M (2M x 8/1M x 16) BIT
MBM29PL160BD 16M (2M x 8/1M x 16) BIT
MBM29PL160TD-75 122 x 32 pixel format, LED Backlight available
相關代理商/技術參數
參數描述
MBM30000 功能描述:BRACKET SIDE MOUNT RoHS:是 類別:工業控制，儀表 >> 配件 系列:* 標準包裝:1 系列:Aero-Motive® 130117 附件類型:拖車帶 適用于相關產品:標準盒式跟蹤系統 其它名稱:WM6183
MBM30035001 制造商:LG Corporation 功能描述:Card,Technical
MBM30035015 制造商:LG Corporation 功能描述:Card,Technical
MBM300A6 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
MBM300GR12A 制造商:n/a 功能描述:IGBT Module
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*