MC10EL15, MC100EL15
http://onsemi.com
5
Table 8. 100EL SERIES NECL DC CHARACTERISTICS VCC = 0 V; VEE = 5.0 V (Note 12)
40°C
25°C
85°C
Symbol
Characteristic
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
IEE
Power Supply Current
25
35
25
35
25
38
mA
VOH
Output HIGH Voltage (Note 13)
1085 1005
880
1025
955
880
1025
955
880
mV
VOL
Output LOW Voltage (Note 13)
1830 1695 1555 1810 1705 1620 1810 1705 1620
mV
VIH
Input HIGH Voltage (SingleEnded)
1165
880
1165
880
1165
880
mV
VIL
Input LOW Voltage (SingleEnded)
1810
1475 1810
1475
mV
VBB
Output Voltage Reference
1.38
1.26
1.38
1.26
1.38
1.26
V
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential) (Note 14)
2.5
0.4
2.5
0.4
2.5
0.4
V
IIH
Input HIGH Current
150
mA
IIL
Input LOW Current
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
12.Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / 0.5 V.
13.Outputs are terminated through a 50 W resistor to VCC 2.0 V.
14. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
Table 9. AC CHARACTERISTICS VCC = 5.0 V; VEE = 0.0 V or VCC= 0 V; VEE = 5.0 V (Note 15)
40°C
25°C
85°C
Symbol
Characteristic
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
fMAX
Maximum Toggle Frequency
1.25
GHz
tPLH
tPHL
Propagation Delay
CLK to Q (Diff)
CLK to Q (SE)
SCLK to Q
460
410
660
710
470
420
670
720
500
450
470
700
750
ps
tSKEW
Part-to-Part Skew
Within-Device Skew (Note 16)
200
50
200
50
200
50
ps
tJITTER
Random Clock Jitter (RMS)
2.6
ps
tS
Setup Time EN
150
ps
tH
Hold Time EN
400
ps
VPP
Input Swing (Note 17)
150
1000
150
1000
150
1000
mV
tr
tf
Output Rise/Fall Times Q
(20% 80%)
325
575
325
575
325
575
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
15.10 Series: VEE can vary +0.06 V / 0.5 V.
100 Series: VEE can vary +0.8 V / 0.5 V.
16.Skews are specified for identical LOWtoHIGH or HIGHtoLOW transitions.
17.VPP(min) is minimum input swing for which AC parameters guaranteed. The device has a DC gain of ≈ 40.