MC100EP16F
http://onsemi.com
5
Table 6. DC CHARACTERISTICS, NECL VCC = 0 V; VEE = 5.5 V to 3.0 V (Note 11) 40°C
25°C
85°C
Symbol
Characteristic
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
IEE
Power Supply Current
23
28
40
25
34
45
26
33
45
mA
VOH
Output HIGH Voltage (Note
12)
1145 1020
895
1145 1020
895
1145 1020
895
mV
VOL
Output LOW Voltage (Note
12)1775 1610 1525 1775 1610 1525 1775 1610 1525
mV
VIH
Input HIGH Voltage (SingleEnded)
1225
880
1225
880
1225
880
mV
VIL
Input LOW Voltage (SingleEnded)
1810
1625 1810
1625
mV
VBB
Output Voltage Reference
1525 1425 1325 1525 1425 1325 1525 1425 1325
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
VEE+2.0
0.0
VEE+2.0
0.0
VEE+2.0
0.0
V
IIH
Input HIGH Current
150
mA
IIL
Input LOW Current
D
0.5
150
0.5
150
0.5
150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
11. Input and output parameters vary 1:1 with VCC.
12.All loading with 50 W to VCC 2.0 V.
13.Not recommended for SingleEnded operation when using an EP16F to drive another EP16F. VOL has reduced output swing and may not
meet the VIL specification over temperature.
14.VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 7. AC CHARACTERISTICS VCC = 0 V; VEE = 3.0 V to 5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 15) 40°C
25°C
85°C
Symbol
Characteristic
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
fmax
Maximum Toggle Frequency
(See Figure 2. Fmax/JITTER) > 4
GHz
tPLH,
tPHL
Propagation Delay to Output
Differential
170
210
250
180
220
260
200
250
300
ps
tSKEW
Duty Cycle Skew
5.0
20
5.0
20
5.0
20
ps
tJITTER
CycletoCycle Jitter (RMS)
(See Figure 2. Fmax/JITTER) 0.2
< 1
0.2
< 1
0.2
< 1
ps
VPP
Input Voltage Swing
(Differential Configuration)
150
800
1200
150
800
1200
150
800
1200
mV
tr
tf
Output Rise/Fall Times
Q
(20% 80%)
70
85
110
80
100
120
90
110
130
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
15.Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC2.0 V.