- 您現在的位置：買賣IC網 > PDF目錄359129 > MC13192SARDUG (飛思卡爾半導體(中國)有限公司) Sensor Applications Reference Design (SARD) PDF資料下載
參數資料
| 型號： | MC13192SARDUG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Sensor Applications Reference Design (SARD) |
| 中文描述： | 傳感器應用的參考設計（可持續農業和鄉村） |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 685K |
| 代理商： | MC13192SARDUG |
1-6
Sensor Applications Reference Design (SARD) User’s Guide
MOTOROLA
Introduction and Configuration
1.3.3 Power Capability
The SARD can be powered from a 5.5 to 9 V supply connected to J106 or a 9 V battery connected to the
board-mounted battery terminals. See Figure 1-4 for J106 and battery terminal placement. If the
accelerometers are not used, 2.0-3.4V can be supplied on J103. In this configuration, the accelerometer
outputs are indeterminate.
1.3.4 LEDs and Switches
D101 through D104 and Switches S101 through S104 are connected to I/O as shown on the SARD
schematic and in Figure 1-4. These are useful as indicators and control in applications. Connections to
MCU ports are listed in Table 1-1. The on-off switch, S105 is labeled on the board.
1.3.5 Board Reset Function
A hardware reset can be performed on the SARD in two ways:
The Reset push button.
The MCU resets the SARD as part of its startup sequence when power is applied and the On/Off
switch is turned on.
In both cases, the reset sequence resets the MCU which, in turn, resets the MC13192.
1.3.6 MCU General Purpose Input/Output (GPIO)
Figure 1-4 shows the MCU GPIO that can be interfaced with external hardware such as sensors. When
using the on-board accelerometers, shunts must be installed at PTB0, PTB1, and PTB7, which corresponds
to pins 1 and 2, 3 and 4, 11 and 12, of J105, to connect the accelerometer ICs to the MCU. For user defined
applications, these shunts can be removed and other hardware attached to the GPIO pins.
1.3.7 BDM Port
Header J101 is a BDM port for use with a P&E BDM-Multilink cable which is available from Metrowerks.
The BDM cable is used with CodeWarrior Development Studio for the HCS08 to program the MCU
flash memory as well as performing in-circuit debugging. See Figure 1-4 for the position of pin 1. The red
lead of the BDM cable must align to pin 1 of J101.
Table 1-1. LED and Switch Port Connection
LED/Switch
MCU Port
I/O
LED 1, D101
PTD0
Output
LED 2, D102
PTD1
Output
LED 3, D103
PTD3
Output
LED 4, D104
PTD4
Output
RESET, S106
RESET
-----
S101
PTA2
Input
S102
PTA3
Input
S103
PTA4
Input
S104
PTA5
Input
F
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC13201 | MC1320x RF Daughter Card(MC1320x RF子卡) |
| MC13211 | ZigBee- Compliant Platform - 2.4 GHz Low Power Transceiver for the IEEE 802.15.4 Standard plus Microcontroller(ZigBee平臺- 為IEEE 802.15.4標準和微控制器設計的2.4 GHz低功率收發器) |
| MC14467P | Low-Power CMOS Ionization Smoke Detector IC |
| MC14467P1 | Other Analog Circuits |
| MC14467P-1 | Low-Power CMOS Ionization Smoke Detector IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC13193 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:2.4 GHz Low Power Transceiver for the IEEE 802.15.4 Standard |
| MC13193EVB-A00 | 功能描述:Zigbee/802.15.4開發工具 MC13192 EVAL BOARD RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:EM35x 頻率:2.4 GHz 接口類型:USB 工作電源電壓: |
| MC13193EVB-BDM-A00 | 功能描述:Zigbee/802.15.4開發工具 MC13192 BOARD W/BDM RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:EM35x 頻率:2.4 GHz 接口類型:USB 工作電源電壓: |
| MC13193EVK-A00 | 功能描述:Zigbee/802.15.4開發工具 MC13192 EVAL KIT RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:EM35x 頻率:2.4 GHz 接口類型:USB 工作電源電壓: |
| MC13193FC | 功能描述:射頻收發器 COMPLETE ZIGBEE STAK 802.15.4 PHY/MAC RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。