- 您現在的位置：買賣IC網 > PDF目錄359132 > MC33390 (飛思卡爾半導體(中國)有限公司) J-1850 SERIAL TRANSCEIVER(串行J-1850總線收發器) PDF資料下載
參數資料
| 型號： | MC33390 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | J-1850 SERIAL TRANSCEIVER(串行J-1850總線收發器) |
| 中文描述： | 殲1850串行收發器（串行的J - 1850總線收發器） |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 450K |
| 代理商： | MC33390 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
33390
9
SYSTEM/APPLICATION INFORMATION
INTRODUCTION
The 33390 is a serial transceiver device designed to meet
the SAE Standard J-1850 Class B performance for bi-
directional half-duplex communication. The device is packaged
in an economical surface-mount SOIC plastic package. An
internal block diagram of the device is shown in Figure 1.
The 33390 derives its robustness to temperature and voltage
extremes from being built on a SMARTMOS process,
incorporating CMOS logic, bipolar/MOS analog circuitry, and
DMOS power FETs. Though the 33390 was principally
designed for automotive applications requiring SAE J-1850
Class B standards, it is suited for other serial communication
applications. It is parametrically specified over an ambient
temperature range of -40
°
C
≤
T
A
≤
125
°
C and 7.0 V
≤
V
BAT
≤
16 V supply. The economical 8-pin SOICN surface mount
plastic package makes the device a cost-effective solution.
FUNCTIONAL DESCRIPTION
Input Power (V
BAT
Pin)
This is the only required input power source necessary to
operate the 33390. The internal voltage reference of the 33390
will remain fully operational with a minimum of 9.0 V on this pin.
Bus transmissions can continue with battery voltages down to
5.0 V. The bus
output voltage will follow the battery voltage
down and, in doing so, track approximately 1.6 V below the
battery voltage. The device will continue to receive and transmit
bus data to the microcontroller with battery voltages as low as
4.25 V. The pin can withstand voltages from -0.3 V to 40 V. If
reverse battery protection is required, an appropriate diode
must be placed in series with this pin to protect the IC.
Sleep Input (
SLEEP
Pin)
This input is used to enable and disable the Class B
transmitter. The Class B receiver is always enabled so long as
adequate V
BAT
pin voltage is applied. When the
SLEEP
pin
voltage is 5.0 V, the Class B transmitter is enabled. If this input
is 0 V, the Class B transmitter will be disabled and less than
65 μA of current will be drawn by the V
BAT
pin. The pin also
provides a 5.0 V reference, internal to the device, used to
establish the Rx output level and slew rate times.
Class B Functional Description
The transmitter provides an analog waveshaped 0 V to 7.0 V
waveform on the BUS
output. It also receives waveforms and
transmits a digital level signal back to a logic IC. The transmitter
can drive up to 32 secondary Class B transceivers (see
Figures 8 and 9). These secondary nodes may be at ground
potentials that are
±
2.0 V relative to the control assembly.
Waveshaping will only be maintained during 2 of the 4 corners
when the 0 to
±
2.0 V ground potential difference condition
exists. The 33390 is a secondary node on the Class B bus.
Each secondary transceiver has a 470
±
10% pF capacitor on
its output for EMI suppression purposes, as well as a 10.6 k
±
5% pull-down resistor to ground. The primary node has a
3300
±
10% pF capacitor on its output for EMI suppression, as
well as a 1.5 k
±
5% pull-down resistor to ground. With more
than 26 nodes, there is no primary node (see Figure 10). All
nodes will have a 470
±
10% pF capacitor and a 10.6 k
±
5%
pull-down resistor. No matter how many secondary nodes are
on the Class B bus, the RC time constant of the Class B bus is
maintained at approximately 5.0 μs. The minimum and
maximum capacitance and resistance on the Class B bus is
given by the expressions shown in Table 1, page 10.
Figure 8. Minimum Bus Load
Figure 9. Maximum Number of Nodes
Figure 10. Maximum Bus Load
3300 pF
1.5 k
470 pF
10.6 k
One Primary Node
1.5 k
470 pF
10.6 k
Primary Node
442
24 Secondary Nodes
3300 pF
11280 pF
14570 pF
342
470 pF
10.6 k
31 Secondary Nodes
F
Freescale Semiconductor, Inc.
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33394 | Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(帶有多個線性穩壓器和高速CAN收發器的開關方式電源) |
| MC33395 | Three-Phase Gate Driver IC(3相柵極驅動器) |
| MC33397 | Dual/Hex Low-Side Switch with Both SPI and Parallel Input Control(帶SPI和并口輸入控制的2或6低端開關) |
| MC33399 | “Local Interconnect Network” Physical Interface(“本地互聯網”（LIN）物理接口) |
| MC33486 | Dual High Side Switch for H-Bridge Automotive Applications(適合于H橋自動應用的雙高端開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33390D | 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MC33390DR2 | 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MC33390EF | 制造商:Freescale Semiconductor 功能描述: |
| MC33394DH | 功能描述:IC POWER SUPPLY MULT-OUT 44-HSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| MC33395DWB | 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。