- 您現在的位置：買賣IC網 > PDF目錄359133 > MC33702 (飛思卡爾半導體(中國)有限公司) 3.0 A Switch-Mode Power Supply with Linear Regulator(3.0 A開關方式電源，帶線性穩壓器) PDF資料下載
參數資料
| 型號： | MC33702 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 3.0 A Switch-Mode Power Supply with Linear Regulator(3.0 A開關方式電源，帶線性穩壓器) |
| 中文描述： | 3.0開關模式電源，線性穩壓器（3.0甲開關方式電源，帶線性穩壓器） |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 841K |
| 代理商： | MC33702 |
33702
16
Go to: www.freescale.com
Figure 12. Inverted Power Up/Down Sequence in +5.0 V
Supply System
Standard Power Sequencing
When the power supply IC operates in the Standard Power
Sequencing mode, the switcher output provides the core
voltage for the microprocessor. This situation and operating
conditions are illustrated in
Figure 10
and
Figure 11
.
Table 2
,
page 15, shows the Power Sequencing mode selection.
Inverted Power Sequencing
When the power supply IC is operating in the Inverted Power
Sequencing mode, the linear regulator (LDO) output provides
the core voltage for the microprocessor, as illustrated in
Figure 12
.
Table 2
shows the Power Sequencing mode
selection.
33702 POWER SEQUENCING
Requirements
1. I/O supply voltage not to exceed core voltage by more than
2.0 V.
2. Core supply voltage not to exceed I/O voltage by more
than 0.4 V.
Methods of Control
The 33702 has several methods of monitoring and
controlling the regulator output voltages, as described in the
paragraphs below. Power sequencing control is also achieved
through the intrinsic operation of the regulators. The EN1 and
EN2 pins can be used to disable the power sequencing (refer to
Table 2
, page 15.
Intrinsic Operation
For both the LDO and switcher, whenever the output voltage
is below the regulation point, the LDO external Pass FET will be
on or the Buck High-Side FET will be on at a duty cycle
controlled by the switcher. Because these devices are FETs,
current can flow in either direction, balancing the voltages via
the common supply pin. The ability to maintain the FETs on will
depend on the available gate voltage, and thus the size of the
boost regulator storage capacitor.
Standard Power Sequencing Control
Comparators monitor voltage differences between the LDO
(LDO pin) and the switcher (V
OUT
pin) outputs as follows:
1.
LDO > V
OUT
+ 1.8 V, turn off LDO.
The LDO can be
forced off. This occurs whenever the LDO output voltage
exceeds the switcher output voltage by more than 1.8 V.
2.
LDO > V
OUT
+ 1.9 V, shunt LDO to ground.
If turning off
the LDO is insufficient and the LDO output voltage
exceeds the switcher output voltage by more than 1.9 V,
a 1.0
shunt FET is turned on that discharges the LDO
load capacitor to ground. The shunt FET is used for
switcher output shorts to ground and for power down in
case of V
IN1
≠
V
IN2
with the switcher output falling faster
than the LDO.
3.
LDO < V
OUT
+ 1.7 V, cancel (1) and (2) above, re-enable
LDO.
Normal operation resumes when the LDO output
voltage is less than 1.7 V above the switcher output
voltage.
4.
LDO < V
OUT
- 0.2 V, turn off switcher.
The switcher can
be forced off. This occurs whenever the LDO is less than
V
OUT
- 0.2 V.
5.
LDO < V
OUT
- 0.3 V, turn on Sync (LS) FET and 1.0
V
OUT
sink FET.
The Buck High-Side FET is forced off and
the Sync FET is forced on. This occurs when the switcher
output voltage exceeds the LDO output by more than
300 mV.
6.
LDO > V
OUT
, reset (4) and (5) above.
Normal operation
resumes when LDO > V
OUT
.
V = 2.0 V
Max. Lead
V = 0.4 V
Max. Lag
V = 0.4 V
Max. Lag
V Start-Up
3.3 V I/O Voltage (V
OUT
)
1.8 V Core Voltage(V
LDO
)
5.0 V Input Supply
V = 2.0 V
Max. Lead
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33742 | System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver(帶增強型高速CAN收發器的系統基片) |
| MC33790 | Two-Channel Distributed System Interface (DSI) Physical Interface Device(2通道分布式系統接口（DSI）物理接口) |
| MC33793 | Distributed System Interface (DSI) Sensor Interface(分布式系統接口（DSI）傳感器接口) |
| MC33794 | Electric Field Imaging Device(電場成像設備) |
| MC33880 | Configurable Octal Serial Switch with Serial Peripheral Interface I/O(可配置的8串行開關,帶串行外圍I/O口(SPI)) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33720 | 制造商:PRIVATE LABEL 功能描述:AXIAL FAN, 254MM, 125VAC, 1A, Supply Voltage:125VAC, Flow Rate - Imperial:935cu. |
| MC33730EK | 功能描述:開關變換器、穩壓器與控制器 SW MODE P/S W/ MULT REG RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MC33730EKR2 | 功能描述:開關變換器、穩壓器與控制器 SW MODE P/S W/ MULT REG RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MC3373P | 制造商:Motorola Inc 功能描述: |
| MC33742DW | 功能描述:網絡控制器與處理器 IC SBC-E-HS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。