- 您現在的位置：買賣IC網 > PDF目錄359133 > MC33742 (飛思卡爾半導體(中國)有限公司) System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver(帶增強型高速CAN收發器的系統基片) PDF資料下載
參數資料
| 型號： | MC33742 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | CAN |
| 英文描述： | System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver(帶增強型高速CAN收發器的系統基片) |
| 中文描述： | 系統基礎芯片的增強型（SBC）的高速CAN收發器（帶增強型高速的CAN收發器的系統基片） |
| 文件頁數： | 18/52頁 |
| 文件大?。?/td> | 1087K |
| 代理商： | MC33742 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
33742
18
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
SYSTEM/APPLICATION INFORMATION
INTRODUCTION
The 33742 and the 33742S are integrated circuits dedicated
to automotive applications. Their functions include the
following:
One fully protected voltage regulator with 200 mA total
output current capability available at the V
DD
terminal.
Driver for external pass transistor for V2 regulator
function.
V
DD
regulator undervoltage reset function, programmable
window or timeout software watchdog function.
Two running modes: Normal and Standby modes when
the microcontroller is running.
Sleep and Stop modes for operation in low power mode to
reduce the application current consumption, while offering
wake-up capability from CAN interface, L3:L0 wake-up
input, and automatic timer wake-up.
Programmable wake-up input and cyclic sense wake-up.
CAN high-speed physical interface with bus failure
diagnostic and enhanced protection feature for TXD and
RXD failure.
Interface with micro through SPI. Interrupt output to report
device status, diagnostic, and wake-up event.
FUNCTIONAL TERMINAL DESCRIPTION
RXD and TXD
The RXD and TXD terminals (receive data terminal and
transmit data terminal, respectively) are connected to the
microcontroller CAN protocol handler. TXD is an input and
controls the CANH and CANL line state (dominant when TXD is
LOW, recessive when TXD is HIGH). RXD is an output and
reports the bus state (RXD LOW when CAN bus is dominant,
HIGH when CAN bus is recessive).
V
DD
The V
DD
terminal is the output terminal of the 5.0 V internal
regulator. It can deliver up to 200 mA. This output is protected
against overcurrent and overtemperature. It includes an
overtemperature pre-warning flag, which is set when the
internal regulator temperature exceeds 130°C typical. When
the temperature exceeds the overtemperature shutdown
(170°C typical), the regulator is turned off.
V
DD
includes an undervoltage reset circuitry, which sets the
RST
terminal LOW when V
DD
is below the undervoltage reset
threshold.
RST
The Reset terminal
RST
is an output that is set LOW when
the device is in reset mode. The
RST
terminal is set HIGH when
the device is not in reset mode.
RST
includes an internal pullup
current source. When
RST
is LOW, the sink current capability is
limited, allowing
RST
to be shorted to 5.0 V for software debug
or software download purposes.
INT
The Interrupt terminal
INT
is an output that is set LOW when
an interrupt occurs.
INT
is enabled using the Interrupt Register
(INTR). When
INT
occurs,
INT
stays LOW until the
INT
source
is cleared.
INT
output also reports a wake-up event by a 10
μ
s typical
pulse when the device is in stop mode.
V2
The V2 terminal is the input sense of the V2 regulator. It is
connected to the external ballast transistor. V2 is also the 5.0 V
supply of the internal CAN interface. It is possible to connect V2
to an external 5.0 V regulator or to the V
DD
output when no
external ballast transistor is used. In this case, the V2CTRL
terminal must be left open. Refer to
Figure 28, 33742 Typical
Application Schematic
, page 46.
V2CTRL
The V2CTRL terminal is the output drive of the V2 regulator
connected to the external ballast transistor.
V
SUP
The V
SUP
terminal is the battery supply input of the device.
HS
The HS terminal is the internal high-side driver output. It is
internally protected against overcurrent and overtemperature.
L0, L1, L2, and L3
The L0:L3 input terminals can be connected to external
switches or any IC’s output. The state of the inputs can be read
by SPI. Theses inputs can be used as wake-up events when the
device is set in Sleep or Stop mode.
CANH and CANL
The CAN High and CAN Low terminals are the interfaces to
the CAN bus lines. They are controlled by TXD input level, and
the state of CANH and CANL is reported through RXD output.
A 60
impedance termination is connected between CANH
and CANL.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33790 | Two-Channel Distributed System Interface (DSI) Physical Interface Device(2通道分布式系統接口（DSI）物理接口) |
| MC33793 | Distributed System Interface (DSI) Sensor Interface(分布式系統接口（DSI）傳感器接口) |
| MC33794 | Electric Field Imaging Device(電場成像設備) |
| MC33880 | Configurable Octal Serial Switch with Serial Peripheral Interface I/O(可配置的8串行開關,帶串行外圍I/O口(SPI)) |
| MC33882 | Six-Output Low-Side Switch with SPI and Parallel Input Control(帶SPI和并口輸入控制的6輸出低端開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33742DW | 功能描述:網絡控制器與處理器 IC SBC-E-HS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33742DWR2 | 功能描述:網絡控制器與處理器 IC SBC-E-HS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33742EP | 功能描述:CAN 接口集成電路 SBC_ECAN_HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33742EPR2 | 功能描述:CAN 接口集成電路 SBC_ECAN_HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33742PEG | 功能描述:CAN 接口集成電路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。