參數資料
型號: MC3374FTB
廠商: MOTOROLA INC
元件分類: 接收器
英文描述: LOW VOLTAGE SINGLE CONVERSION FM RECEIVER
中文描述: FM, AUDIO SINGLE CHIP RECEIVER, PQFP32
封裝: PLASTIC, TQFP-32
文件頁數: 6/8頁
文件大?。?/td> 237K
代理商: MC3374FTB
MC3374
6
MOTOROLA ANALOG IC DEVICE DATA
CIRCUIT DESCRIPTION
The MC3374 is an FM narrowband receiver capable of
operation to 75 MHz. The low voltage design yields low
power drain and excellent sensitivity in narrowband voice
and data link applications. In the typical application the mixer
amplifies the incoming RF or IF signal and converts this
frequency to 455 kHz. The signal is then filtered by a 455 kHz
ceramic filter and applied to the first intermediate frequency
(IF) amplifier input, before passing through a second ceramic
filter. The modulated IF signal is then applied to the limiting IF
amplifier and detector circuitry. Modulation is recovered by a
conventional quadrature detector. The typical modulation
bandwidth available is 3.0 to 5.0 kHz.
Features available include buffers for audio/data
amplification and active filtering, on board voltage regulator,
low battery detection circuitry with programmable level, and
receiver disable circuitry. The MC3374 is an FM utility
receiver to be used for voice and/or narrowband data
reception. It is especially suitable where extremely low power
consumption and high design flexibility are required.
APPLICATION
The MC3374 can be used as a high performance FM IF for
the use in low power dual conversion receivers. Because of
the MC3374’s extremely good sensitivity (0.6
μ
V for 20 dB
(S+N/N, see Figure 3)), it can also be used as a stand alone
single conversion narrowband receiver to 75 MHz for
applications not sensitive to image frequency interference.
An RF preamplifier will likely be needed to overcome
preselector losses.
The oscillator is a Colpitts type which must be run under
crystal control. For fundamental mode crystals choose
resonators, parallel resonant, for a 32 pF load. For higher
frequencies, use a 3rd overtone series mode type. The coil
L2 and RD resistor are needed to ensure proper operation.
The best adjacent channel and sensitivity response occur
when two 455 kHz ceramic filters are used, as shown in
Figure 1. Either can be replaced by a 0.1
μ
F coupling
capacitor to reduce cost, but some degradation in sensitivity
and/or stability is suspected.
The detector is a quadrature type, with the connection
from the limiter output to the detector input provided
internally. A 455 kHz LC tank circuit must be provided
externally. One of the tank pins (Pin 8) must be decoupled
using a 0.1
μ
F capacitor. The 56 k
damping resistor (see
Figure 1), determines the peak separation of the detector
(and thus its bandwidth). Smaller values will increase the
separation and bandwidth but decrease recovered audio and
sensitivity.
The data buffer is a noninverting amplifier with a nominal
voltage gain of 2.7 V/V. This buffer needs its dc bias
(approximately 250 mV) provided externally or else
debiasing will occur. A 2nd order Sallen–Key low pass filter,
as shown in Figure 1, connecting the recovered audio output
to the data buffer input provides the necessary dc bias and
some post detection filtering. The buffer can also be used as
an active filter.
The audio buffer is a noninverting amplifier with a nominal
voltage gain of 4.0 V/V. This buffer is self–biasing so its input
should be ac coupled. The two buffers, when applied as
active filters, can be used together to allow simultaneous
audio and very low speed data reception. Another possible
configuration is to receive audio only and include a
noise–triggered squelch.
The comparator is a noninverting type with an open
collector output. Typically, the pull–up resistor used between
Pin 14 and VCC is 100 k
. With RL = 100 k
the comparator
is capable of operation up to 25 kHz. The circuit is
self–biasing, so its input should be ac coupled.
The regulator is a 1.07 V reference capable of sourcing
3.0 mA. This pin (Pin 17) needs to be decoupled using a
1.0–10
μ
F capacitor to maintain stability of the MC3374.
All three VCCs on the MC3374 (VCC, VCC2, VCC3) run on
the same supply voltage. VCC is typically decoupled using
capacitors only. VCC2 and VCC3 should be bypassed using
the RC bypasses shown in Figure 1. Eliminating the resistors
on the VCC2 and VCC3 bypasses may be possible in some
applications, but a reduction in sensitivity and quieting will
likely occur.
The low battery detection circuit gives an NPN open
collector output at Pin 20 which drops low when the MC3374
supply voltage drops below 1.2 V. Typically it would be pulled
up via a 100 k
resistor to supply.
The 1.2 V Select pin, when connected to the MC3374 supply,
programs the low battery detector to trip at VCC < 1.1 V. Leaving
this pin open raises the trip voltage on the low battery detector.
Pin 15 is a receiver enable which is connected to VCC for
normal operation. Connecting this pin to ground shuts off
receiver and reduces current drain to ICC < 0.5
μ
A.
APPENDIX
Design of 2nd Order Sallen–Key Low Pass Filters
Input
R1
R2
C2
C1
Bias
Avo = K
Low Pass Output
0 to fo Hz
+
The audio and data buffers can easily be configured as active
low pass filters using the circuit configuration shown above.
The circuit has a center frequency (fo) and quality factor (Q)
given by the following:
fo
1
2
R1R2C1C2
1
R1C2
R2C1
Q
R2C2
R1C1
(1–K)
R1C1
R2C2
If possible, let R1 = R2 or C1 = C2 to simplify the above
equations. Be sure to avoid a negative Q value to prevent
instability. Setting Q
1
2
filter response.
0.707 yields a maximally flat
相關PDF資料
PDF描述
MC3374 LOW VOLTAGE SINGLE CONVERSION FM RECEIVER
MC34001BU JFET Input Operational Amplifiers
MC34001U JFET Input Operational Amplifiers
MC34062 METER DPM LED 3.5DIGIT GREEN
MC34062P1 PIN-PROGRAMMABLE OVERVOLTAGE SENSING CIRCUIT
相關代理商/技術參數
參數描述
MC33761SNT1025 制造商:ON SEMI 功能描述:New
MC33761SNT1-025 功能描述:低壓差穩壓器 - LDO 2.5V 80mA Output RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MC33761SNT1-025G 功能描述:低壓差穩壓器 - LDO 2.5V 80mA Output w/Enable Low Noise RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MC33761SNT1-028 功能描述:低壓差穩壓器 - LDO 2.8V 80mA Output RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MC33761SNT1-028G 功能描述:低壓差穩壓器 - LDO 2.8V 80mA Output w/Enable Low Noise RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20