參數資料
型號： MC33889
廠商： 飛思卡爾半導體(中國)有限公司
元件分類： 基準電壓源/電流源
英文描述： System Basis Chip (SBC) with Low Speed Fault Tolerant CAN Interface
中文描述： 帶有低速CAN的精簡版系統基礎芯片
文件頁數： 12/30頁
文件大?。?/td> 464K
代理商： MC33889
PC33889
12
PC33889
4
DEVICE DESCRIPTION
Introduction:
The MC33889 is an integrated circuit dedicated to automotive applications. It includes the following functions:
- One full protected voltage regulator with 200mA total output current capability.
- Driver for external path transistor for V2 regulator function.
- Reset, programmable watchdog function
- Four operational modes
- Wake up capabilities: Forced wake up, cyclic sense and wake up inputs, CAN and SPI
- Can low speed fault tolerant physical interface, compatible with Motorola MC33388D.
4.1
Device Supply
The device is supplied from the battery line through the Vsup pin. An external diode is required to protect against negative
transients and reverse battery. It can operate from 4.5V and under the jump start condition at 27V DC. This pin sustains standard
automotive voltage conditions such as load dump at 40V. When Vsup falls below 3V typical the MC33889 detects it and store the
information into the SPI register, in a bit called “BATFAIL”. This detection is available in all operation modes.
4.2
Vdd1 Voltage Regulator
Vdd1 Regulator is a 5V output voltage with total current capability of 200mA. It includes a voltage monitoring circuitry
associated with a reset function. The Vdd1 regulator is fully protected against over current, short-circuit and has over
temperature detection warning flags and shutdown with hysteresis.
4.3
V2 regulator
V2 Regulator circuitry is designed to drive an external path transistor in order to increase output current flexibility. Two pins
are used: V2 and V2 ctrl. Output voltage is 5V and is realized by a tracking function of the Vdd1 regulator. Recommended ballast
transistor is MJD32C. Other transistor might be used, however depending upon PNP gain an external resistor capacitor network
might be connected between emitter and base of PNP. The use of external ballast is optional (refer to simplified typical
application). State of V2 is reported into IOR register (if V2 is below 4.5V typical in case of over load or short circuit).
4.4
HS1 Vbat Switch Output
HS1 output is a 2 ohms typical switch from Vsup pin. It allows the supply of external switches and their associated pull up or
pull down circuitry, in conjunction with the wake up input pins for example. Output current is limited to 200mA and HS1 is
protected against short-circuit and has an over temperature shutdown (reported in IOR register). HS1 output is controlled from
the internal register and SPI. It can be activated at regular intervals in sleep mode thanks to internal timer. It can also be
permanently turned on in normal or stand-by modes to drive external loads such as relays or supply peripheral components. In
case of inductive load drive external clamp circuitry must be added.
4.5
Functional Modes
The device has four modes of operation, stand-by, normal, stop and sleep modes. All modes are controlled by the SPI. An
additional temporary mode called “normal request mode” is automatically accessed by the device (refer to state machine) after
wake up events. Special mode and configuration are possible for software application debug and flash memory programming.
4.5.1
Normal mode:
In this mode both regulators are ON and this corresponds to the normal application operation. All functions are available in
this mode (watchdog, wake up input reading through SPI, HS1 activation, CAN communication). The software watchdog is
running and must be periodically cleared through SPI.
4.5.2
Standby mode:
Only the regulator 1 is ON. Regulator 2 is turned OFF by disabling the V2 ctrl pin. The CAN cell is not available, as powered
from V2, other functions are available: wake up input reading through SPI, HS1 activation. The watchdog is running.
4.5.3
Sleep mode:
Regulators 1 and 2 are OFF. In this mode, the MCU is not powered. In this mode, the device can be awakened internally by
cyclic sense via the wake up inputs pins and HS1 output, from the forced wake function, the CAN physical interface, and SPI
(CSB pin).
4.5.4
Stop mode
Regulator 2 is turned OFF by disabling the V2 ctrl pin. The regulator 1 is activated in a special low power mode which allow to
deliver 2 mA. The objective is to maintain the MCU of the application supplied while it is turned into power saving condition (i.e
stop or wait mode).
Stop mode is entered through SPI. Stop mode is dedicated to power the Microcontroller when it is in low power mode (stop,
pseudo stop, wait etc.). In these mode the MCU supply current is less than 1mA. The MCU can restart its software application
very quickly, without the complete power up and reset sequence.
When the application is in stop mode (both MCU and SBC), the application can wake up from the SBC side (ex cyclic sense,
forced wake up, CAN message, wake up inputs) or the MCU side (key wake up etc.).
When Stop mode is selected by SPI, stop mode becomes active 20us after end of SPI message. The “go to stop” instruction
must be the last instruction executed by the MCU before going to low power mode.
For More Information On This Product,
Go to: www.freescale.com
F
Freescale Semiconductor, Inc.
n
.
相關PDF資料
PDF描述
MC33897 Single-Wire CAN Transceiver(單線CAN收發器)
MC33972 Multiple Switch Detection Interface with Suppressed Wake-Up(帶抑制喚醒功能的多開關檢測接口)
MC33976 Dual Gauge Driver with Configurable Response Time(帶可設置響應時間的雙標尺驅動器)
MC33984 Dual Intelligent High-Current Self-Protected Silicon High-Side Switch (4.0 mOhm)(雙智能大電流帶自保護功能的硅高端開關（4mOhm）)
MC33989 System Basis Chip with High Speed CAN Transceiver(帶高速CAN收發器的系統基片)
相關代理商/技術參數
參數描述
MC33889BDW 功能描述:網絡控制器與處理器 IC SBC LIGHT PASS 3.3 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33889BDWR2 功能描述:網絡控制器與處理器 IC SBC LIGHT PASS 3.3 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33889BPEG 制造商:Freescale Semiconductor 功能描述:SYSTEM BASIS CHIP WITH LOW SPEED FAULT TOLERANT CAN INTERFACE 制造商:Freescale Semiconductor 功能描述:SBC-LITE-LS-CAN - Bulk 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN 28SOIC
MC33889BPEGR2 制造商:Freescale Semiconductor 功能描述:CAN 125Kbps Sleep/Stop 9V/12V/15V T/R 制造商:Freescale Semiconductor 功能描述:SBC-LITE-LS-CAN - Tape and Reel 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN 28SOIC
MC33889DDW 功能描述:網絡控制器與處理器 IC SBC LIGHT REV D RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*