- 您現在的位置：買賣IC網 > PDF目錄11546 > MC33889DW (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF資料下載
參數資料
| 型號： | MC33889DW |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 22/59頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 標準包裝： | 26 |
| 控制器類型： | 系統基礎芯片 |
| 接口： | CAN |
| 電源電壓： | 5.5 V ~ 18 V |
| 電流 - 電源： | 45mA |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
33889
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
CYCLIC SENSE WAKE-UP (CYCLIC SENSE TIMER AND WAKE-UP INPUTS L0, L1)
The SBC can wake-up from a state change of one of the wake-up input lines (L0, L1), while the external pullup or pulldown
resistor of the switches associated to the wake-up input lines are biased with HS1 VSUP switch. The HS1 switch is activated in
sleep or stop mode from an internal timer. Cyclic sense and forced wake-up are exclusive. If Cyclic sense is enabled, the forced
wake-up can not be enabled.
INFO FOR CYCLIC SENSE + DUAL EDGE SELECTION
In case the Cyclic sense and Lx both level sensitive conditions are use together, the initial value for Lx inputs are sampled in
two cases:
1) When the register LPC[D3 and D0] are set and
2) At cyclic sense event, that is when device is in sleep or stop mode and HS1 is active.
The consequence is that when the device wake up by Lx transition, the new value is sampled as default, then when the device
is set back into low power again, it will automatically wake up.
The user should reset the LPC bits [D3 and D0] to 0 and set them again to the desired value prior to enter sleep or stop
mode.
FORCED WAKE-UP
The SBC can wake-up automatically after a predetermined time spent in sleep or stop mode. Forced wake-up is enabled by
setting bit FWU in the LPC register. Cyclic sense and forced wake-up are exclusive. If forced wake-up is enabled, the Cyclic
sense can not be enabled.
CAN WAKE-UP
The device can wake-up from a CAN message. A CAN wake-up cannot be disabled.
SPI WAKE-UP
The device can wake-up by the CS pin in sleep or stop mode. Wake-up is detected by the CS pin transition from a low to high
level. In stop mode this correspond to the condition where the MCU and SBC are both in Stop mode, and when the application
wake-up events come through the MCU.
SYSTEM POWER UP
At power up the device automatically wakes up.
DEVICE POWER UP, SBC WAKE UP
After device or system power up or a wake-up from sleep mode, the SBC enters into “reset mode” then into “normal request
mode”.
BATTERY FALL EARLY WARNING
This function provides an interrupt when the VSUP voltage is below the 6.1 V typical. This interrupt is maskable. A hysteresis
is included. Operation is only in Normal and Stand-by modes. VBAT low state reports in the IOR register.
RESET AND WDOG OPERATION
The following figure shows the reset and watchdog output operations. Reset is active at device power up and wake-up. Reset
is activated in case the VDD1 falls or the watchdog is not triggered. The WDOG output is active low as soon as the reset goes
low and stays low for as long as the watchdog is not properly re-activated by the SPI.
The WDOG output pin is a push pull structure than can drive external components of the application, for instance to signal the
MCU is in a wrong operation. Even if it is internally turned on (low-state), the reset pin can be forced to 5.0 V at 25 °C only, thanks
to its internally limited current drive capability. The WDOG stays low until the Watchdog register is properly addressed through
the SPI.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33389CDW | IC SYSTEM BASE W/CAN 28-SOIC |
| MC33388DR2 | IC TOLERANT CAN INT FAULT 14SOIC |
| PX0414 | CONN SMB JACK PNL MNT RG174 |
| PIC16LF1937-E/PT | IC PIC MCU FLASH 512KX14 44-TQFP |
| PIC16F1934-E/ML | IC PIC MCU FLASH 256KX7 44-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33889DWR2 | 功能描述:IC SYSTEM BASE W/CAN 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| MC33895FC | 功能描述:IC H-BRIDGE QUAD W/LIN 32-QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MC33897AEF | 功能描述:網絡控制器與處理器 IC SWCAN PB FREE P 2.4 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33897AEFR2 | 功能描述:網絡控制器與處理器 IC SWCAN PB FREE P 2.4 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33897BEF | 功能描述:網絡控制器與處理器 IC SINGLE WIRE CAN 8 LEAD RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。