- 您現在的位置：買賣IC網 > PDF目錄1948 > MC33989DWR2 (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF資料下載
參數資料
| 型號： | MC33989DWR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 14/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 標準包裝： | 1 |
| 控制器類型： | 系統基礎芯片 |
| 接口： | CAN |
| 電源電壓： | 5.5 V ~ 18 V |
| 電流 - 電源： | 45mA |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 剪切帶 (CT) |
| 配用： | KIT33989DWEVB-ND - KIT EVAL 33989DW HS SBC |
| 其它名稱： | MC33989DWR2CT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
33989
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
STANDBY MODE
Only regulator 1 is ON. Regulator 2 is turned OFF by disabling the V2 control pin. Only the wake-up capability of the CAN
interface is available. Other functions available are wake-up input reading through SPI and HS1 activation. The Watchdog is
running.
NORMAL MODE
In this mode, both regulators are ON. This corresponds to the normal application operation. All functions are available in this
mode (Watchdog, wake-up input reading through SPI, HS1 activation, CAN communication). The software Watchdog is running
and must be periodically cleared through SPI.
STOP MODE
Regulator 2 is turned OFF by disabling the V2 control pin. The regulator 1 is activated in a special low power mode, allowing
to deliver few mA. The objective is to maintain the MCU of the application supplied while it is turned into power saving condition
(i.e Stop or Wait modes). In Stop mode the device supply current from VBAT is very low.
When the application is in Stop mode (both MCU and SBC), the application can wake-up from the SBC side (for example:
cyclic sense, forced wake-up, CAN message, wake-up inputs and overcurrent on VDD1), or the MCU side (key wake-up, etc.).
Stop mode is always selected by the SPI. In Stop mode the software Watchdog can be running or idle depending upon
selection by the SPI (RCR, bit WDSTOP). To clear the watchdog, the SBC must be awakened by a CS pin (SPI wake-up). In
Stop mode, SBC wake-up capability are identical as in Sleep mode. Please refer to Table 5.
SLEEP MODE
Regulators 1 and 2 are OFF. The current from VSUP pin is reduced. In this mode, the device can be awakened internally by
cyclic sense via the wake-up inputs pins and HS1 output, from the forced wake-up function and from the CAN physical interface.
When a wake-up occurs the SBC goes first into reset mode before entering Normal Request mode.
RESET MODE
In this mode, the Reset (RST) pin is low and a timer is running for a time RSTDUR. After this time is elapsed, the SBC enters
Normal Request mode. Reset mode is entered if a reset condition occurs (VDD1 low, watchdog timeout or watchdog trigger in a
closed window).
NORMAL REQUEST MODE
This is a temporary mode automatically accessed by the device after the reset mode, or after the SBC wake-up from
Stop mode. After wake-up from the Sleep mode or after the device power-up, the SBC enters the Reset mode before entering
the Normal Request mode. After a wake-up from the Stop mode, the SBC enters Normal Request mode directly.
In Normal Request mode the VDD1 regulator is ON, V2 is OFF, the reset pin is high. As soon as the device enters the Normal
Request mode an internal 350 ms timer is started. During these 350 ms the microcontroller of the application must address the
SBC via the SPI, configuring the Watchdog register. This is the condition for the SBC to stop the 350 ms timer and to go into the
Normal or Standby mode and to set the watchdog timer according to configuration.
NORMAL REQUEST ENTERED AND NO WD CONFIGURATION OCCURS
In case the Normal Request mode is entered after SBC power-up, or after a wake-up from Stop mode, and if no WD
configuration occurs while the SBC is in Normal Request mode, the SBC goes to Reset mode after the 350 ms time period is
expired before again going into Normal Request mode. If no WD configuration is achieved, the SBC alternatively goes from
Normal Request into reset, then Normal Request modes etc.
In case the Normal Request mode is entered after a wake-up from Sleep mode, and if no WD configuration occurs while the
SBC is in Normal Request mode, the SBC goes back to Sleep mode.
APPLICATION WAKE-UP FROM SBC SIDE
When an application is in Stop mode, it can wake-up from the SBC side. When a wake-up is detected by the SBC (for example,
CAN, Wake-up input, etc.) the SBC turns itself into Normal Request mode and generates an interrupt pulse at the INT pin.
相關PDF資料 |
PDF描述 |
|---|---|
| MC3488ADR2G | IC LINE DRIVER DUAL EIA 8-SOIC |
| MC34940EGR2 | IC IMAGING DEVICE ELEC 24-SOICW |
| MC44BS373CAFCR2 | IC MODULATOR AUD/VID U/V 20-QFN |
| MC44BS374CAEFR2 | IC AUDIO/VIDEO MODULATOR 16-SOIC |
| MC44BS374T1AEFR2 | IC AUDIO/VIDEO MODULATOR 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33989PEG | 功能描述:CAN 接口集成電路 SBC-HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33989PEGR2 | 功能描述:CAN 接口集成電路 SBC-HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33990D | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MC33990DR2 | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MC33991DW | 制造商:Freescale Semiconductor 功能描述:Gauge Driver Integrated Circuit |
發布緊急采購，3分鐘左右您將得到回復。