- 您現在的位置：買賣IC網 > PDF目錄69027 > MC68HC05P4ADWE (FREESCALE SEMICONDUCTOR INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 PDF資料下載
參數資料
| 型號： | MC68HC05P4ADWE |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 |
| 封裝： | SOIC-28 |
| 文件頁數： | 36/72頁 |
| 文件大?。?/td> | 400K |
| 代理商： | MC68HC05P4ADWE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
MC68HC05P4A Data Sheet, Rev. 7.1
Freescale Semiconductor
41
Chapter 9
Computer Operating Properly (COP)
9.1 Introduction
This device includes a watchdog computer operating properly (COP) feature as a mask option. The COP
is implemented with an 18-bit ripple counter. This provides a timeout period of 64 milliseconds at a bus
rate of 2 MHz. If the COP should time out, a system reset will occur and the device will be re-initialized in
the same fashion as a power-on reset (POR) or external reset.
9.2 Resetting the COP
Preventing a COP reset is done by writing a 0 to the COPR bit. This action will reset the counter and begin
the timeout period again. The COPR bit is bit 0 of address $1FF0. A read of address $1FF0 will access
the user-defined ROM data at that location.
9.3 COP During Wait or Halt Mode
The COP will continue to operate normally during wait or halt mode. The software should pull the device
out of wait or halt mode periodically and reset the COP by writing a logic 0 to the COPR bit to prevent a
COP reset.
9.4 COP During Stop Mode
Stop mode disables the oscillator circuit and thereby turns the clock off for the entire device. The COP
counter will be reset when stop mode is entered. If a reset is used to exit stop mode, the COP counter will
be reset after the 4064 cycles of delay after stop mode. If an IRQ is used to exit stop mode, the COP
counter will not be reset after the 4064-cycle delay and will have that many cycles already counted when
control is returned to the program.
NOTE
Halt mode is not intended for normal use. This feature is provided to keep
the COP watchdog timer active in the event a STOP instruction is
inadvertently executed.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC05P4APE | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP28 |
| MC68HC05P4ADW | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 |
| MC68HC05P6VS | 8-BIT, 2.1 MHz, MICROCONTROLLER, CDIP28 |
| MC68HC05P6CS | 8-BIT, 2.1 MHz, MICROCONTROLLER, CDIP28 |
| MC68HC05P6VP | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05P4DW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
| MC68HC05P4P | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
| MC68HC05P6 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
| MC68HC05P6_1 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
| MC68HC05P8 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
發布緊急采購，3分鐘左右您將得到回復。