- 您現在的位置：買賣IC網 > PDF目錄371047 > MC68HC05X16 (Motorola, Inc.) 8-Bit Microcontroller Units (MCU).(8位微控制器) PDF資料下載
參數資料
| 型號： | MC68HC05X16 |
| 廠商： | Motorola, Inc. |
| 英文描述： | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 中文描述： | 8位微控制器單元（MCU）。（8位微控制器） |
| 文件頁數： | 86/232頁 |
| 文件大小： | 1095K |
| 代理商： | MC68HC05X16 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁
MOTOROLA
5-24
MC68HC05X16
Rev. 1
MOTOROLA CAN MODULE (MCAN)
5
If several CAN modules are driving a dominant level on the bus at the same time then the values
for V
CANH
and V
CANL
can go to 0.3 and 4.7 volts respectively. The residual 0.3 V is due to the
voltage drop across the diodes and driver transistors in the transmission circuit.
The receiver part of the network uses two identical voltage divider networks, with a divide ratio of
6:1 (resistor values of 150k
and 30k
) referenced to V
DD
/2. This increases the common mode
range of the input comparator on the physical bus lines. If the common mode range of the
comparator at its inputs is 1.5 to 3.5 volts then, for V
DD
= 5.0 V, the common mode range will be
increased to –3.5 to +8.5 volts on the bus lines.
5.4.1
Single wire operation
In the event of a bus fault occurring, limited operation of the MCAN bus may still be possible,
depending on the nature of the fault. If the fault is due to a short circuit between the two bus lines
or between one of the lines and ground, battery voltage or some other potential, it is possible to
identify (using a special software procedure) the line on which the fault exists and to switch the
corresponding comparator input from the faulty line to the V
DD
/2 reference supply. At the same
time the driver transistors to the faulty line should also be switched off. This will allow
communication to continue on the bus. One result of this mode of one wire transmission is a
significant reduction in the common mode range of the input comparator.
Switching to one wire operation is achieved using the control bits RX0-passive and RX1-passive
in the MCAN command register, located at address $21. Setting either of these bits will result in
the corresponding input being disconnected from the bus and connected to V
DD
/2.
5.5
Sleep mode
If the SLEEP bit in the MCAN command register is set by the processor the MCAN will go to sleep,
unless it is active. If there is activity on the MCAN bus lines, or there is an interrupt pending, the
MCAN is deemed to be active and will not go to sleep; a wake-up interrupt will be generated by
the MCAN in these circumstances. The SLEEP bit may also be cleared by the processor, in which
case no wake-up interrupt will be generated. Note that this bit is write-only by the CPU, and it is
not possible therefore to check whether sleep mode has been entered by reading it. However, the
CAF bit in the EEPROM control register is set when the MCAN is asleep, and cleared when it is
woken up (see
Section 3.5.1
).
In order to minimize power consumption, the active comparator is switched off and the sleep
comparator circuitry is used to detect activity on the bus. When in sleep mode the MCAN stops its
own clocks, leaving the MCU in normal run mode. (Similarly a STOP instruction will stop the
processor clocks, leaving the MCAN in run mode.) The on-chip oscillator will stop only if the MCAN
is in sleep mode and the MCU executes a STOP instruction. There is a time delay between the
STOP instruction being executed and the oscillator stopping. During this time it is possible that the
MCAN will come out of sleep mode, and hence prevent the oscillator from stopping.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC05X32 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| MC68HC705X32 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| MC68HC05X4 | HCMOS Microcontroller Unit |
| MC68HC05X4CDW | HCMOS Microcontroller Unit |
| MC68HC05X4DW | HCMOS Microcontroller Unit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05X32 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor HCMOS) microcontroller unit |
| MC68HC05X4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit |
| MC68HC05X4CDW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit |
| MC68HC05X4DW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit |
| MC68HC08AB16A | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。