參數資料
型號: MC68HC11D0CFBE3
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP44
封裝: 10 X 10 MM, QFP-44
文件頁數: 67/124頁
文件大?。?/td> 6875K
代理商: MC68HC11D0CFBE3
RESETS AND INTERRUPTS
TECHNICAL DATA
5-3
Semiconductor wafer processing causes variations of the RC time-out values between
individual devices. An E-clock frequency below 10 kHz is detected as a clock monitor
error. An E-clock frequency of 200 kHz or more prevents clock monitor errors. Using
the clock monitor function when the E clock is below 200 kHz is not recommended.
Special considerations are needed when a STOP instruction is executed and the clock
monitor is enabled. Because the STOP function causes the clocks to be halted, the
clock monitor function generates a reset sequence if it is enabled at the time the STOP
mode was initiated. Before executing a STOP instruction, clear the CME bit in the OP-
TION register to zero to disable the clock monitor. After recovery from STOP, set the
CME bit to logic one to enable the clock monitor.
5.1.5 Option Register
*Can be written only once in first 64 cycles out of reset in normal modes, or at any time in special modes.
Bits [7:6] and 2 — Not implemented
Always read zero
IRQE — Configure IRQ for Edge Sensitive Only Operation
This bit can be written only once during the first 64 E-clock cycles after reset in normal
modes.
0 = Low level recognition
1 = Falling edge recognition
DLY — Enable Oscillator Startup Delay
This bit is set during reset and can be written only once during the first 64 E-clock cy-
cles after reset in normal modes. If an external clock source rather than a crystal is
used, the stabilization delay can be inhibited because the clock source is assumed to
be stable.
0 = No stabilization delay on exit from STOP
1 = Stabilization delay enabled on exit from STOP
CME — Clock Monitor Enable
This control bit can be read or written at any time and controls whether or not the in-
ternal clock monitor circuit triggers a reset sequence when the system clock is slow or
absent. When it is clear, the clock monitor circuit is disabled. When it is set, the clock
monitor circuit is enabled. Reset clears the CME bit.
CR[1:0] — COP Timer Rate Select
These control bits determine a scaling factor for the watchdog timer.
OPTION — System Configuration Options
$0039
Bit 7
654321
Bit 0
0
IRQE*
DLY*
CME
0
CR1*
CR0*
RESET:
00010000
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68HC711D0CFN3 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PQCC44
MC68HC11E0CP3 8-BIT, 3 MHz, MICROCONTROLLER, PDIP48
MC68HC11E0CP3 8-BIT, 3 MHz, MICROCONTROLLER, PDIP48
MC68HC11E0FU 8-BIT, MICROCONTROLLER, PQFP64
MC68HCP11E1CFU2 8-BIT, 2 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
MC68HC11D0CFBE3R 功能描述:8位微控制器 -MCU 8B MCU 192RAM 3 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11D0CFN2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Microcontrollers
MC68HC11D0CFN3 制造商: 功能描述: 制造商:undefined 功能描述:
MC68HC11D0CFNE2 功能描述:8位微控制器 -MCU 8B MCU 192 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11D0CFNE2R 功能描述:8位微控制器 -MCU 8B MCU 192 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT