參數資料
型號: MC68HC11D3CFB
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, 2 MHz, MICROCONTROLLER, PQFP44
封裝: QFP-44
文件頁數: 125/131頁
文件大?。?/td> 1640K
代理商: MC68HC11D3CFB
MC68HC11D3
TIMING SYSTEM
MOTOROLA
TECHNICAL DATA
9-7
polarity of the pulse being produced. After a match occurs, the output compare register
is reprogrammed to change the output pin back to its inactive level at the next match.
A value representing the width of the pulse is added to the original value, and then writ-
ten to the output compare register. Because the pin state changes occur at specific
values of the free-running counter, the pulse width can be controlled accurately at the
resolution of the free-running counter, independent of software latencies. To generate
an output signal of a specific frequency and duty cycle, repeat this pulse-generating
procedure.
There are four 16-bit read/write output compare registers: TOC1, TOC2, TOC3, and
TOC4, and the TI4/O5 register, which functions under software control as either IC4
or OC5. Each of the OC registers is set to $FFFF on reset. A value written to an OC
register is compared to the free-running counter value during each E-clock cycle. If a
match is found, the particular output compare flag is set in timer interrupt flag register
1 (TFLG1). If that particular interrupt is enabled in the timer interrupt mask register 1
(TMSK1), an interrupt is generated. In addition to an interrupt, a specified action can
be initiated at one or more timer output pins. For OC5–OC2, the pin action is controlled
by pairs of bits (OMx and OLx) in the TCTL1 register. The output action is taken on
each successful compare, regardless of whether or not the OCxF flag in the TFLG1
register was previously cleared.
OC1 is different from the other output compares in that a successful OC1 compare can
affect any or all five of the OC pins. The OC1 output action taken when a match is
found is controlled by two 8-bit registers with three bits unimplemented: the output
compare 1 mask register, OC1M, and the output compare 1 data register, OC1D.
OC1M specifies which port A outputs are to be used, and OC1D specifies what data
is placed on these port pins.
9.3.1 Timer Output Compare Registers
All output compare registers are 16-bit read-write. Each is initialized to $FFFF at reset.
If an output compare register is not used for an output compare function, it can be used
as a storage location. A write to the high-order byte of an output compare register pair
inhibits the output compare function for one bus cycle. This inhibition prevents inap-
propriate subsequent comparisons. Coherency requires a complete 16-bit read or
write. However, if coherency is not needed, byte accesses can be used.
For output compare functions, write a comparison value to output compare registers
TOC1–TOC4 and TI4/O5. When TCNT value matches the comparison value, speci-
fied pin actions occur.
相關PDF資料
PDF描述
MC68L11D0CFBE2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP44
MC68HC711D3CFN1 8-BIT, OTPROM, MICROCONTROLLER, PQCC44
MC68L11D0CFB2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP44
MC68L11D0FN2 8-BIT, 2 MHz, MICROCONTROLLER, PQCC44
MC68HC11D0CFN3R2 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQCC44
相關代理商/技術參數
參數描述
MC68HC11D3CFB1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11D3CFB3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11D3CFB4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11D3CFN 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11D3CFN1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers