- 您現在的位置：買賣IC網 > PDF目錄45226 > MC68HC711D3CFN1 (MOTOROLA INC) 8-BIT, OTPROM, MICROCONTROLLER, PQCC44 PDF資料下載
參數資料
| 型號： | MC68HC711D3CFN1 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 90/131頁 |
| 文件大小： | 1640K |
| 代理商： | MC68HC711D3CFN1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁當前第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
MC68HC11D3
RESETS AND INTERRUPTS
MOTOROLA
TECHNICAL DATA
5-17
nals driving on-chip peripheral functions can be shut down. The CPU is always shut
down during WAIT. While in the wait state, the address/data bus repeatedly runs read
cycles to the address where the CCR contents were stacked. The MPU leaves the wait
state when it senses any interrupt that has not been masked.
The free-running timer system is shut down only if the I bit is set to one and the COP
system is disabled by NOCOP being set to one. Several other systems can also be in
a reduced power consumption state depending on the state of software-controlled
configuration control bits. The SPI system is enabled or disabled by the SPE control
bit. The SCI transmitter is enabled or disabled by the TE bit, and the SCI receiver is
enabled or disabled by the RE bit. Therefore the power consumption in WAIT is de-
pendent on the particular application.
5.5.2 STOP
Executing the STOP instruction while the S bit in the CCR is equal to zero places the
MCU in the STOP condition. If the S bit is not zero, the STOP opcode is treated as a
no-op (NOP). The STOP condition offers minimum power consumption because all
clocks, including the crystal oscillator, are stopped while in this mode. To exit STOP
and resume normal processing, a logic low level must be applied to one of the external
interrupts (IRQ or XIRQ), or to the RESET pin. A pending edge-triggered IRQ can also
bring the CPU out of STOP.
Because all clocks are stopped in this mode, all internal peripheral functions also stop.
The data in the internal RAM is retained as long as VDD power is maintained. The CPU
state and I/O pin levels are static and are unchanged by STOP. Therefore, when an
interrupt comes to restart the system, the MCU resumes processing as if there were
no interruption. If reset is used to restart the system a normal reset sequence results
where all I/O pins and functions are also restored to their initial states.
To use the IRQ pin as a means of recovering from STOP, the I bit in the CCR must be
clear (IRQ not masked). The XIRQ pin can be used to wake up the MCU from STOP
regardless of the state of the X bit in the CCR, although the recovery sequence de-
pends on the state of the X bit. If X is set to zero (XIRQ not masked), the MCU starts
up, beginning with the stacking sequence leading to normal service of the XIRQ re-
quest. If X is set to one (XIRQ masked or inhibited), then processing continues with
the instruction that immediately follows the STOP instruction, and no XIRQ interrupt
service is requested or pending.
Because the oscillator is stopped in STOP mode, a restart delay may be imposed to
allow oscillator stabilization upon leaving STOP. If the internal oscillator is being used,
this delay is required; however, if a stable external oscillator is being used, the DLY
control bit can be used to bypass this startup delay. The DLY control bit is set by reset
and can be optionally cleared during initialization. If the DLY equal to zero option is
used to avoid startup delay on recovery from STOP, then reset should not be used as
the means of recovering from STOP, as this causes DLY to be set again by reset, im-
posing the restart delay. This same delay also applies to power-on-reset, regardless
of the state of the DLY control bit, but does not apply to a reset while the clocks are
running.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68L11D0CFB2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP44 |
| MC68L11D0FN2 | 8-BIT, 2 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC11D0CFN3R2 | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQCC44 |
| MC68L11D0CFB2R2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC11D3CFB1 | 8-BIT, OTPROM, 1 MHz, MICROCONTROLLER, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC711D3CFN2 | 功能描述:IC MCU 2MHZ 4K OTP 44-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
| MC68HC711D3CFNE2 | 功能描述:8位微控制器 -MCU 8B OTP 192RAM 2 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC711D3CFNE3 | 功能描述:8位微控制器 -MCU 8B OTP 192RAM 2 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC711D3VFNE2 | 功能描述:8位微控制器 -MCU 8B OTP 192RAM 2 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC711E20CFN2 | 功能描述:IC MCU 20K 2MHZ OTP 52-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
發布緊急采購，3分鐘左右您將得到回復。