參數資料
型號: MC68HCL05C8AFB
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, MICROCONTROLLER, PQFP44
封裝: QFP-44
文件頁數: 69/116頁
文件大小: 781K
代理商: MC68HCL05C8AFB
Serial Communications Interface (SCI)
MC68HC05C8A MC68HCL05C8A MC68HSC05C8A Data Sheet, Rev. 5.1
56
Freescale Semiconductor
TC — Transmission Complete Bit
This clearable, read-only bit is set when the TDRE bit is set, and no data, preamble, or break character
is being transmitted. TC generates an interrupt request if the TCIE bit in SCCR2 is also set. Clear the
TC bit by reading the SCSR with TC set, and then writing to the SCDR. Reset sets the TC bit. Software
must initialize the TC bit to logic 0 to avoid an instant interrupt request when turning on the transmitter.
1 = No transmission in progress
0 = Transmission in progress
RDRF — Receive Data Register Full Bit
This clearable, read-only bit is set when the data in the receive shift register transfers to the SCI data
register. RDRF generates an interrupt request if the RIE bit in SCCR2 is also set. Clear the RDRF bit
by reading the SCSR with RDRF set, and then reading the SCDR. Reset clears the RDRF bit.
1 = Received data available in SCDR
0 = Received data not available in SCDR
IDLE — Receiver Idle Bit
This clearable, read-only bit is set when 10 or 11 consecutive logic 1s appear on the receiver input.
IDLE generates an interrupt request if the ILIE bit in SCCR2 is also set. Clear the IDLE bit by reading
the SCSR with IDLE set, and then reading the SCDR. Reset clears the IDLE bit.
1 = Receiver input idle
0 = Receiver input not idle
OR — Receiver Overrun Bit
This clearable, read-only bit is set if the SCDR is not read before the receive shift register receives the
next word. OR generates an interrupt request if the RIE bit in SCCR2 is also set. The data in the shift
register is lost, but the data already in the SCDR is not affected. Clear the OR bit by reading the SCSR
with OR set and then reading the SCDR. Reset clears the OR bit.
1 = Receiver shift register full and RDRF = 1
0 = No receiver overrun
NF — Receiver Noise Flag
This clearable, read-only bit is set when noise is detected in data received in the SCI data register.
Clear the NF bit by reading the SCSR and then reading the SCDR. Reset clears the NF bit.
1 = Noise detected in SCDR
0 = No noise detected in SCDR
FE — Receiver Framing Error Flag
This clearable, read-only flag is set when there is a logic 0 where a stop bit should be in the character
shifted into the receive shift register. If the received word causes both a framing error and an overrun
error, the OR bit is set and the FE bit is not set. Clear the FE bit by reading the SCSR, and then reading
the SCDR. Reset clears the FE bit.
1 = Framing error
0 = No framing error
相關PDF資料
PDF描述
MC68HC05C8AVFB 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44
MC68HSC05C8CFN 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQCC44
MC68HSC05C8CFB 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP44
MC68HC05C8APE 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40
MC68HC05C8AMB 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP42
相關代理商/技術參數
參數描述
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
MC68HCP11E0CP2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HCP11E0FN 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN,SCI,SPI 外圍設備:POR,PWM,溫度傳感器,WDT 輸入/輸出數:21 程序存儲器容量:40KB(20K x 16) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HCP11E0FNE 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT