- 您現在的位置：買賣IC網 > PDF目錄371048 > MC68HCP11A1CFN2 (MOTOROLA INC) HCMOS Single-Chip Microcontroller PDF資料下載
參數資料
| 型號： | MC68HCP11A1CFN2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HCMOS Single-Chip Microcontroller |
| 中文描述： | 8-BIT, 2 MHz, MICROCONTROLLER, PQCC52 |
| 封裝： | PLASTIC, LCC-52 |
| 文件頁數： | 72/158頁 |
| 文件大?。?/td> | 776K |
| 代理商： | MC68HCP11A1CFN2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁當前第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
MOTOROLA
8-2
PROGRAMMABLE TIMER, RTI, AND PULSE ACCUMULATOR
MC68HC11A8
TECHNICAL DATA
8
The result obtained by an input capture corresponds to the value of the counter one E
clock cycle after the transition which triggered the edge-detection logic. The selected
edge transition sets the ICxF bit in timer interrupt flag register 1 (TFLG1) and can
cause an interrupt if the corresponding ICxl bit(s) is (are) set in the timer interrupt mask
register 1 (TMSK1). A read of the input capture register’s most significant byte inhibits
captures for one E cycle to allow a double-byte read of the full 16-bit register.
8.1.3 Output Compare
All output compare registers are 16-bit read/write registers which are initialized to
$FFFF by reset. They can be used as output waveform controls or as elapsed time
indicators. If an output compare register is not used, it may be used as a storage loca-
tion.
All output compare registers have a separate dedicated comparator for comparing
against the free-running counter. If a match is found, the corresponding output com-
pare flag (OCxF) bit in TFLG1 is set and a specified action is automatically taken. For
output compare functions two through five the automatic action is controlled by pairs
of bits (OMx and OLx) in the timer control register 1 (TCTL1). Each pair of control bits
are encoded to specify the output action to be taken as a result of a successful OCx
compare. The output action is taken on each successful compare regardless of wheth-
er or not the OCxF flag was previously clear.
An interrupt can also accompany a successful output compare, provided that the cor-
responding interrupt enable bit (OCxl) is set in TMSK1.
After a write cycle to the most significant byte, output compares are inhibited for one
E cycle in order to allow writing two consecutive bytes before making the next compar-
ison. If both bytes of the register are to be changed, a double-byte write instruction
should be used in order to take advantage of the compare inhibit feature.
Writes can be made to either byte of the output compare register without affecting the
other byte.
A write-only register, timer compare force (CFORC), allows forced compares. Five of
the bit positions in the CFORC register correspond to the five output compares. To
force a compare, or compares, a write is done to CFORC register with the associated
bits set for each output compare that is to be forced. The action taken as a result of a
forced compare is the same as if there was a match between the OCx register and the
free-running counter, except that the corresponding interrupt status flag bits are not
set. Output actions are synchronized to the prescaled timer clock so there could be as
much as 16 E clock cycles of delay between the write to CFORC and the output action.
8.1.4 Output Compare 1 I/O Pin Control
Unlike the other four output compares, output compare 1 can automatically affect any
or all of the five output pins (bits 3-7) in port A as a result of a successful compare be-
tween the OC1 register and the 16-bit free-running counter. The two 5-bit registers
used in conjunction with this function are the output compare 1 mask register (OC1M)
and the output compare 1 data register (OC1D).
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HCP11A1CFN3 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CP2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CP3 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1MFN2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1MP2 | HCMOS Single-Chip Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HCP11A1CFN3 | 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HCP11A1FN | 制造商:MOTORALA 功能描述: |
| MC68HCP11E0CP2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC68HCP11E0FN | 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HCP11E0FNE | 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。