參數資料
型號： MC7457RX867NC
廠商： Freescale Semiconductor
文件頁數： 13/71頁
文件大?。?/td> 0K
描述： IC MPU RISC 32BIT 483FCCBGA
標準包裝： 36
系列： MPC74xx
處理器類型： 32-位 MPC74xx PowerPC
速度： 867MHz
電壓： 1.1V
安裝類型： 表面貼裝
封裝/外殼： 483-BCBGA，F(xiàn)CCBGA
供應商設備封裝： 483-FCCBGA（29x29）
包裝： 托盤
MPC7457 RISC Microprocessor Hardware Specifications, Rev. 8
Electrical and Thermal Characteristics
Freescale Semiconductor
20
Figure 4 provides the AC test load for the MPC7457.
Figure 4. AC Test Load
SYSCLK to ARTRY/SHD0/SHD1 high impedance after
precharge
tKHARPZ
—2
tSYSCLK
3, 5,
6, 7
Notes:
1. All input specifications are measured from the midpoint of the signal in question to the midpoint of the rising edge of the input
SYSCLK. All output specifications are measured from the midpoint of the rising edge of SYSCLK to the midpoint of the signal
in question. All output timings assume a purely resistive 50-
Ω load (see Figure 4). Input and output timings are measured at
the pin; time-of-flight delays must be added for trace lengths, vias, and connectors in the system.
2. The symbology used for timing specifications herein follows the pattern of t(signal)(state)(reference)(state) for inputs and
t(reference)(state)(signal)(state) for outputs. For example, tIVKH symbolizes the time input signals (I) reach the valid state (V)
relative to the SYSCLK reference (K) going to the high (H) state or input setup time. And tKHOV symbolizes the time from
SYSCLK(K) going high (H) until outputs (O) are valid (V) or output valid time. Input hold time can be read as the time that
the input signal (I) went invalid (X) with respect to the rising clock edge (KH) (note the position of the reference and its state
for inputs) and output hold time can be read as the time from the rising edge (KH) until the output went invalid (OX).
3. tsysclk is the period of the external clock (SYSCLK) in ns. The numbers given in the table must be multiplied by the period of
SYSCLK to compute the actual time duration (in ns) of the parameter in question.
4. According to the bus protocol, TS is driven only by the currently active bus master. It is asserted low then precharged high
before returning to high impedance as shown in Figure 6. The nominal precharge width for TS is 0.5
× t
SYSCLK, that is, less
than the minimum tSYSCLK period, to ensure that another master asserting TS on the following clock will not contend with
the precharge. Output valid and output hold timing is tested for the signal asserted. Output valid time is tested for
precharge.The high-impedance behavior is guaranteed by design.
5. Guaranteed by design and not tested.
6. According to the bus protocol, ARTRY can be driven by multiple bus masters through the clock period immediately following
AACK. Bus contention is not an issue because any master asserting ARTRY will be driving it low. Any master asserting it
low in the first clock following AACK will then go to high impedance for one clock before precharging it high during the second
cycle after the assertion of AACK. The nominal precharge width for ARTRY is 1.0 tSYSCLK; that is, it should be high
impedance as shown in Figure 6 before the first opportunity for another master to assert ARTRY. Output valid and output
hold timing is tested for the signal asserted.The high-impedance behavior is guaranteed by design.
7. According to the MPX bus protocol, SHD0 and SHD1 can be driven by multiple bus masters beginning the cycle of TS. Timing
is the same as ARTRY, that is, the signal is high impedance for a fraction of a cycle, then negated for up to an entire cycle
(crossing a bus cycle boundary) before being three-stated again. The nominal precharge width for SHD0 and SHD1 is 1.0
tSYSCLK. The edges of the precharge vary depending on the programmed ratio of core to bus (PLL configurations).
8. BMODE[0:1] and BVSEL are mode select inputs and are sampled before and after HRESET negation. These parameters
represent the input setup and hold times for each sample. These values are guaranteed by design and not tested. These
inputs must remain stable after the second sample. See Figure 5 for sample timing.
Table 9. Processor Bus AC Timing Specifications 1 (continued)
At recommended operating conditions. See Table 4.
Parameter
Symbol 2
All Revisions and
Speed Grades
Unit
Notes
Min
Max
Output
Z0 = 50 Ω
OVDD/2
RL = 50 Ω
相關PDF資料
PDF描述
FMC36DRAS CONN EDGECARD 72POS R/A .100 SLD
MC68EC040RC40A IC MPU 32BIT 40MHZ 179-PGA
MPC8560VTAQFC MPU POWERQUICC III 783FCPBGA
MPC8548EVTATGB MPU POWERQUICC III 783-PBGA
MPC8548EPXATGB MPU POWERQUICC III 783-PBGA
相關代理商/技術參數
參數描述
MC7457TRX1000LC 制造商:Freescale Semiconductor 功能描述:MPC74XX RISC 32-BIT 0.13UM 1GHZ 1.5V/1.8V/2.5V 483-PIN FCCBG - Trays
MC7457TRX1000NC 功能描述:微處理器 - MPU APOLO7 RV1.2 1.1V -40C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC7457TRX1267LC 制造商:Freescale Semiconductor 功能描述:MPC74XX RISC 32-BIT 0.13UM 1.267GHZ 1.5V/1.8V/2.5V 483-PIN F - Trays
MC7457VG1000LC 功能描述:微處理器 - MPU APOLO7 RV1.2 1.3V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC7457VG1000NC 功能描述:微處理器 - MPU APOLO7 RV1.2 1.1V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*