- 您現在的位置：買賣IC網 > PDF目錄11431 > MC74HC4316ANG (ON Semiconductor)IC MUX/DEMUX QUAD 1X1 16DIP PDF資料下載
參數資料
| 型號： | MC74HC4316ANG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MUX/DEMUX QUAD 1X1 16DIP |
| 標準包裝： | 500 |
| 系列： | 74HC |
| 功能： | 多路復用器/多路分解器 |
| 電路： | 4 x 1:1 |
| 導通狀態電阻： | 130 歐姆 |
| 電壓電源： | 雙電源 |
| 電壓 - 電源，單路/雙路(±)： | ±2 V ~ 6 V |
| 電流 - 電源： | 40µA |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-DIP |
| 包裝： | 管件 |
| 其它名稱： | MC74HC4316ANG-ND MC74HC4316ANGOS |
MC74HC4316A
http://onsemi.com
8
APPLICATIONS INFORMATION
0
-10
-20
-30
-40
-50
- 100
1.0
2.0
FREQUENCY (kHz)
dBm
-60
-70
-80
-90
FUNDAMENTAL FREQUENCY
DEVICE
SOURCE
Figure 16. Plot, Harmonic Distortion
3.0
The Enable and Control pins should be at VCC or GND
logic levels, VCC being recognized as logic high and GND
being recognized as a logic low. Unused analog
inputs/outputs may be left floating (not connected).
However, it is advisable to tie unused analog inputs and
outputs to VCC or VEE through a low value resistor. This
minimizes crosstalk and feedthrough noise that may be
picked up by the unused I/O pins.
The maximum analog voltage swings are determined by
the supply voltages VCC and VEE. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below VEE. In the example
below, the difference between VCC and VEE is 12 V.
Therefore, using the configuration in Figure 17, a maximum
analog signal of twelve volts peaktopeak can be
controlled.
When voltage transients above VCC and/or below VEE are
anticipated on the analog channels, external diodes (Dx) are
recommended as shown in Figure 18. These diodes should
be small signal, fast turnon types able to absorb the
maximum anticipated current surges during clipping. An
alternate method would be to replace the Dx diodes with
MOSORBs (MOSORB
t is an acronym for high current
surge protectors). MOSORBs are fast turnon devices
ideally suited for precise dc protection with no inherent wear
out mechanism.
ANALOG O/I
ON
16
VCC = 6 V
ANALOG I/O
+ 6 V
-6 V
+ 6 V
-6 V
ENABLE CONTROL
INPUTS
(VCC OR GND)
ON
16
VCC
Dx
VCC
Dx
Figure 17.
Figure 18. Transient Suppressor Application
8
SELECTED
CONTROL
INPUT
Dx
SELECTED
CONTROL
INPUT
+ 6 V
VEE
-6 V
VCC
VEE
ENABLE CONTROL
INPUTS
(VCC OR GND)
VEE
相關PDF資料 |
PDF描述 |
|---|---|
| FSUSB42MUX | IC USB SWITCH DPDT 10MSOP |
| FSUSB46K8X | IC USB SWITCH DPST US8 |
| GRM2195C2AR40CD01D | CAP CER 0.4PF 100V NP0 0805 |
| GRM2195C2A9R9DZ01D | CAP CER 9.9PF 100V NP0 0805 |
| GRM2195C2A9R7DZ01D | CAP CER 9.7PF 100V NP0 0805 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC74HC4316D | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC74HC4316DR2 | 制造商:ON Semiconductor 功能描述:Analog Switch Quad SPST 16-Pin SOIC T/R |
| MC74HC4316F | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC74HC4316FEL | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC74HC4316FL1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。