參數資料
型號: MC9S08LH36CLH
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: MICROCONTROLLER, PQFP64
封裝: 10 X 10 MM, ROHS COMPLIANT, LQFP-64
文件頁數: 2/44頁
文件大?。?/td> 954K
代理商: MC9S08LH36CLH
MC9S08LH64 Series MCU Data Sheet, Rev. 5
Thermal Characteristics
Freescale Semiconductor
10
3.4
Thermal Characteristics
This section provides information about operating temperature range, power dissipation, and package
thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in
on-chip logic and voltage regulator circuits, and it is user-determined rather than being controlled by the
MCU design. To take PI/O into account in power calculations, determine the difference between actual pin
voltage and VSS or VDD and multiply by the pin current for each I/O pin. Except in cases of unusually high
pin current (heavy loads), the difference between pin voltage and VSS or VDD will be very small.
The average chip-junction temperature (TJ) in C can be obtained from:
Table 4. Absolute Maximum Ratings
Rating
Symbol
Value
Unit
Supply voltage
VDD
–0.3 to +3.8
V
Maximum current into VDD
IDD
120
mA
Digital input voltage
VIn
–0.3 to VDD +0.3
V
Instantaneous maximum current
Single pin limit (applies to all port pins)1, 2, 3
1
Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive (VDD) and negative (VSS) clamp
voltages, then use the larger of the two resistance values.
2 All functional non-supply pins, except for PTB2 are internally clamped to V
SS and VDD.
3 Power supply must maintain regulation within operating V
DD range during instantaneous and
operating maximum current conditions. If positive injection current (VIn > VDD) is greater than
IDD, the injection current may flow out of VDD and could result in external power supply going
out of regulation. Ensure external VDD load will shunt current greater than maximum injection
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low (which would reduce overall power
consumption).
ID
25
mA
Storage temperature range
Tstg
–55 to 150
C
Table 5. Thermal Characteristics
Rating
Symbol
Value
Unit
Operating temperature range
(packaged)
TA
TL to TH
–40 to 85
C
Maximum junction temperature
TJ
95
C
Thermal resistance
Single-layer board
80-pin LQFP
JA
55
C/W
64-pin LQFP
73
Thermal resistance
Four-layer board
80-pin LQFP
JA
42
C/W
64-pin LQFP
54
相關PDF資料
PDF描述
MC9S08LH36CLK MICROCONTROLLER, PQFP80
MC9S08LL16CLH 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64
MC9S08LL16CLF 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP48
MC9S08LL16CGT 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, QCC48
MC9S08LL64CLK 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
MC9S08LH36CLK 功能描述:8位微控制器 -MCU S08 36K Flash 80LQFP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC9S08LH64 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Advanced Information
MC9S08LH64CLH 功能描述:8位微控制器 -MCU S08 CPU, 64K FLASH, 64LQFP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC9S08LH64CLK 功能描述:8位微控制器 -MCU S08 CPU, 64K FLASH, 80LQFP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC9S08LL16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit HCS08 Central Processor Unit