- 您現在的位置：買賣IC網 > PDF目錄45290 > MC9S08RC32DWE (FREESCALE SEMICONDUCTOR INC) 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO28 PDF資料下載
參數資料
| 型號： | MC9S08RC32DWE |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO28 |
| 封裝： | ROHS COMPLIANT, MS-013AE, SOIC-28 |
| 文件頁數： | 161/234頁 |
| 文件大?。?/td> | 1758K |
| 代理商： | MC9S08RC32DWE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁當前第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁
Modes of Operation
MC9S08RC/RD/RE/RG Data Sheet, Rev. 1.11
32
Freescale Semiconductor
into stop2, the states of the I/O pins are latched. The states are held while in stop2 mode and after exiting
stop2 mode until a 1 is written to PPDACK in SPMSC2.
Exit from stop2 is done by asserting any of the wakeup pins: RESET, IRQ, or KBI1 that have been enabled,
or through the real-time interrupt. IRQ and KBI1 pins are always active-low when used as wakeup pins in
stop2 regardless of how they were congured before entering stop2. (KBI2 will not wake the MCU from
stop2.)
Upon wakeup from stop2 mode, the MCU will start up as from a power-on reset (POR) except pin states
remain latched. The CPU will take the reset vector. The system and all peripherals will be in their default
reset states and must be initialized.
After waking up from stop2, the PPDF bit in SPMSC2 is set. This ag may be used to direct user code to
go to a stop2 recovery routine. PPDF remains set and the I/O pin states remain latched until a 1 is written
to PPDACK in SPMSC2.
For pins that were congured as general-purpose I/O, the user must copy the contents of the I/O port
registers, which have been saved in RAM, back to the port registers before writing to the PPDACK bit. If
the port registers are not restored from RAM before writing to PPDACK, then the register bits will be in
their reset states when the I/O pin latches are opened and the I/O pins will switch to their reset states.
For pins that were congured as peripheral I/O, the user must recongure the peripheral module that
interfaces to the pin before writing to the PPDACK bit. If the peripheral module is not enabled before
writing to PPDACK, the pins will be controlled by their associated port control registers when the I/O
latches are opened.
3.6.3
Stop3 Mode
Upon entering stop3 mode, all of the clocks in the MCU, including the oscillator itself, are halted. The
OSC is turned off, the ACMP is disabled, and the voltage regulator is put in standby. The states of all of
the internal registers and logic, as well as the RAM content, are maintained. The I/O pin states are not
latched at the pin as in stop2. Instead they are maintained by virtue of the states of the internal logic driving
the pins being maintained.
Exit from stop3 is done by asserting RESET, any asynchronous interrupt pin that has been enabled, or
through the real-time interrupt. The asynchronous interrupt pins are the IRQ or KBI1 and KBI2 pins.
If stop3 is exited by means of the RESET pin, then the MCU will be reset and operation will resume after
taking the reset vector. Exit by means of an asynchronous interrupt or the real-time interrupt will result in
the MCU taking the appropriate interrupt vector.
A separate self-clocked source (
≈1 kHz) for the real-time interrupt allows a wakeup from stop2 or stop3
mode with no external components. When RTIS2:RTIS1:RTIS0 = 0:0:0, the real-time interrupt function
and this 1-kHz source are disabled. Power consumption is lower when the 1-kHz source is disabled, but in
that case the real-time interrupt cannot wake the MCU from stop.
相關PDF資料 |
PDF描述 |
|---|---|
| MC9S08RC60FDE | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, QCC48 |
| MC9S08RE60DWE | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO28 |
| MC9S08RC60CFGE | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| MC9S08RD60FJE | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32 |
| MC9S08RE60FJE | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC9S08RC32FDE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC9S08RC32FG | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Microcontrollers |
| MC9S08RC32FGE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC9S08RC32FJ | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC9S08RC32FJE | 功能描述:IC MCU 32K FLASH 8MHZ 32-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:S08 標準包裝:1 系列:87C 核心處理器:MCS 51 芯體尺寸:8-位 速度:16MHz 連通性:SIO 外圍設備:- 輸入/輸出數:32 程序存儲器容量:8KB（8K x 8） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 6 V 數據轉換器:- 振蕩器型:外部 工作溫度:0°C ~ 70°C 封裝/外殼:44-DIP 包裝:管件 其它名稱:864285 |
發布緊急采購，3分鐘左右您將得到回復。