參數資料
型號: MCIMX31DVKN5D
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 32-BIT, 532 MHz, MICROPROCESSOR, PBGA457
封裝: 14 X 14 MM, 0.50 MM PITCH, ROHS COMPLIANT, PLASTIC, MAPBGA-457
文件頁數: 108/118頁
文件大?。?/td> 1083K
代理商: MCIMX31DVKN5D
Signal Descriptions
MCIMX31/MCIMX31L Technical Data, Rev. 4.3
Freescale Semiconductor
9
3
Signal Descriptions
Signal descriptions are in the reference manual. Special signal considerations are listed following this
paragraph. The BGA ball assignment is in Section 5, “Package Information and Pinout.”
Special Signal Considerations:
Tamper detect (GPIO1_6)
Tamper detect logic is used to issue a security violation. This logic is activated if the tamper detect
input is asserted.
The tamper detect logic is disabled after reset. After enabling the logic, it is impossible to disable
it until the next reset. The GPR[16] bit functions as the tamper detect enable bit.
GPIO1_6 functions similarly to other I/O with GPIO capabilities regardless of the status of the
tamper detect enable bit. (For example, the GPIO1_6 can function as an input with GPIO
capabilities, such as sampling through PSR or generating interrupts.)
Power ready (GPIO1_5)
The power ready input, GPIO1_5, should be connected to an external power management IC power
ready output signal. If not used, GPIO1_5 must either be (a) externally pulled-up to NVCC1 or (b)
a no connect, internally pulled-up by enabling the on-chip pull-up resistor. GPIO1_5 is a dedicated
input and cannot be used as a general-purpose input/output.
SJC_MOD
SJC_MOD must be externally connected to GND for normal operation. Termination to GND
through an external pull-down resistor (such as 1 k
Ω) is allowed, but the value should be much
smaller than the on-chip 100 k
Ω pull-up.
CE_CONTROL
CE_CONTROL is a reserved input and must be externally tied to GND through a 1 k
Ω resistor.
TTM_PAD
This is for Freescale factory use only. Control bits indicate that the pull-up/down is disabled.
However, the TTM_PAD is actually connected to an on-chip pull-down device. Users must either
float this signal or tie it to GND.
M_REQUEST and M_GRANT
These two signals are not utilized internally. The user should make no connection to these signals.
Clock Source Select (CLKSS)
The CLKSS is the input that selects the default reference clock source providing input to the DPLL.
To select CKIH, tie CLKSS to NVCC1. To select CKIL, tie CLKSS to ground. After initialization,
the reference clock source can be changed (initial setting is overwritten) by programming the
PRCS bits in the CCMR.
相關PDF資料
PDF描述
MCIMX31DVMN5D 32-BIT, 532 MHz, MICROPROCESSOR, PBGA473
MCIMX31LDVKN5D 32-BIT, 532 MHz, MICROPROCESSOR, PBGA457
MCIMX31LCJKN5D 32-BIT, 532 MHz, MICROPROCESSOR, PBGA457
MCIMX512DVK8C SPECIALTY MICROPROCESSOR CIRCUIT, PBGA625
MCIMX511DVK8C SPECIALTY MICROPROCESSOR CIRCUIT, PBGA625
相關代理商/技術參數
參數描述
MCIMX31DVKN5DR2 功能描述:處理器 - 專門應用 2.0.1 CONSUMER FULL RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX31DVMN5D 功能描述:處理器 - 專門應用 2.0.1 CONSUMER FULL RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX31DVMN5DR2 功能描述:處理器 - 專門應用 2.0.1 CONSUMER FULL RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX31L 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Multimedia Applications Processors
MCIMX31LC 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Multimedia Applications Processors for Industrial and Automotive Products