參數資料
型號: MCM63P631TQ8
廠商: MOTOROLA INC
元件分類: DRAM
英文描述: 64K x 32 Bit Pipelined BurstRAM Synchronous Fast Static RAM
中文描述: 64K X 32 CACHE SRAM, 8 ns, PQFP100
封裝: TQFP-100
文件頁數: 17/27頁
文件大?。?/td> 328K
代理商: MCM63P631TQ8
MCM63P636
17
MOTOROLA FAST SRAM
FUNCTIONAL OPERATION
POWER UP AND INITIALIZATION
The RESET input is used to reset the SRAM internal logic
at power on. At power on, this pin is held low and then driven
high at some later time. Eight cycles after the RESET is as-
serted high, standard SRAM functionality may begin.
DATA STROBES
The data strobes STRBA, STRBA, STRBB, and STRBB
are driven by the SRAM to be used by the device receiving
the output data. The data strobes toggle only at the approxi-
mate center of each output data valid window such that the
external device can reliably latch in this data. Following a
burst read, the data strobes will be driven to High–Z.
WRITE CYCLES
The address is sampled on the first rising edge of clock of
each burst write sequence, and the write data is sampled on
the subsequent rising clock edges. During a burst write the
last, last two, or last three addresses may be blocked from
being written by asserting the W synchronous write pin high.
However, once W is asserted high, it must remain in this
state through the remainder of the burst write sequence. All
burst write (and masked write) sequences must be followed
by an inactive cycle to reset internal state machines.
LOW POWER STOP–CLOCK OPERATION
In the stop–clock mode of operation, the SRAM will hold all
state and data values even though the clock is not running
(full static operation). The SRAM design allows the clock to
start with ADS, and stops the clock after the last write data is
latched, or the last read data is driven out.
When starting and stopping the clock, the initial clocks be-
ing driven may not meet the AC clock timing parametrics, but
will meet those parametrics at least two clocks prior to ADS
being asserted low.
To achieve the lowest power operation for all three stop
clock modes, stop read, stop write, and stop deselect:
Force the clock to a low state.
Force the control signals to an inactive state (this guar-
antees any potential source of noise on the clock input
will not start an unplanned on activity).
Force the address inputs to a low state (VIL), preferably
< 0.2 V.
VIL
K
ADS
SA
Din
Qout
A
B
VIH
VIL
VIL
HIGH–Z
HIGH–Z
STOP–CLOCK WITH READ TIMING
ADS
INITIATES
BURST READ
END
BURST
READ
K
CLOCK
STOP
STOP–CLOCK
LOW POWER
OPERATION
WAKE–UP/
INVALID
CLOCK
INVALID
CLOCK
FIRST
VALID
CLOCK
Q(A)
Q(A +1)
Q(A +2)
Q(A +3)
相關PDF資料
PDF描述
MCM63P636TQ200 64K x 36 Bit Pipelined BurstRAM Synchronous Fast Static RAM
MCM63P636TQ200R Replaced by PTH12000W :
MCM63P736 Replaced by PTH12000W :
MCM63P736TQ100R Replaced by PTH12000W :
MCM63P736TQ133R 128K x 36 and 256K x 18 Bit Pipelined BurstRAM Synchronous Fast Static RAM
相關代理商/技術參數
參數描述
MCM63P631TQ8R 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:64K x 32 Bit Pipelined BurstRAM Synchronous Fast Static RAM
MCM63P636 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:64K x 36 Bit Pipelined BurstRAM Synchronous Fast Static RAM
MCM63P636TQ200 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:64K x 36 Bit Pipelined BurstRAM Synchronous Fast Static RAM
MCM63P636TQ200R 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:64K x 36 Bit Pipelined BurstRAM Synchronous Fast Static RAM
MCM63P636ZP200 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:64K x 36 Bit Pipelined BurstRAM Synchronous Fast Static RAM