- 您現在的位置：買賣IC網 > PDF目錄383585 > MCP1630V (Microchip Technology Inc.) High-Speed, Microcontroller-Adaptable, Pulse Width Modulator PDF資料下載
參數資料
| 型號： | MCP1630V |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | High-Speed, Microcontroller-Adaptable, Pulse Width Modulator |
| 中文描述： | 高速微控制器適應性，脈寬調制器 |
| 文件頁數： | 11/26頁 |
| 文件大?。?/td> | 268K |
| 代理商： | MCP1630V |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
2005 Microchip Technology Inc.
DS21896B-page 11
MCP1630/MCP1630V
3.0
MCP1630 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE
3.1
Error Amplifier Output Pin (COMP)
COMP is an internal error amplifier output pin. External
compensation is connected from the FB pin to the
COMP pin for control-loop stabilization. An internal
voltage clamp is used to limit the maximum COMP pin
voltage to 2.7V (typ.). This clamp is used to set the
maximum peak current in the power system switch by
setting a maximum limit on the CS input for Peak
Current mode control systems.
3.2
Error Amplifier Inverting Input
(FB)
FB is an internal error amplifier inverting input pin. The
output (voltage or current) is sensed and fed back to
the FB pin for regulation. Inverting or negative
feedback is used.
3.3
Current Sensing Input (CS)
CS is the current sense input pin used for cycle-by-
cycle control for Peak Current mode converters. The
MCP1630 is typically used for sensed current
applications to reduce the current sense signal, thus
reducing power dissipation.
For Voltage mode or Average Current mode
applications, a ramp is used to compare the error
amplifier output voltage with producing the PWM duty
cycle. For applications that require higher signal levels,
the MCP1630V is used to increase the level from a
maximum of 0.9V (MCP1630) to 2.7V (MCP1630V).
The common mode voltage range for the MCP1630V
CS input is V
IN
-1.4V. For normal PWM operation, the
CS input should be less than or equal to V
IN
- 1.4V at
all times.
3.4
Oscillator Input (OSC)
OSC is an external oscillator input pin. Typically, a
microcontroller I/O pin is used to generate the OSC
input. When high, the output driver pin (V
EXT
) is driven
low. The high-to-low transition initiates the start of a
new cycle. The duty cycle of the OSC input pin deter-
mines the maximum duty cycle of the power converter.
For example, if the OSC input is low for 75% of the time
and high for 25% of the time, the duty cycle range for
the power converter is 0% to 75% maximum.
3.5
Ground (GND)
Connect the circuit ground to the GND pin. For most
applications, this should be connected to the analog or
quiet ground plane. Noise on this ground can affect the
sensitive cycle-by-cycle comparison between the CS
input and the error amplifier output.
3.6
External Driver Output Pin (V
EXT
)
V
EXT
is an external driver output pin, used to determine
the power system duty cycle. For high-power or high-
side drives, this output should be connected to the logic-
level input of the MOSFET driver. For low-power, low-
side applications, the V
EXT
pin can be used to directly
drive the gate of an N-channel MOSFET.
3.7
Input Bias Pin (V
IN
)
V
IN
is an input voltage pin. Connect the input voltage
source to the V
IN
pin. For normal operation, the voltage
on the V
IN
pin should be between +3.0V and +5.5V. A
0.1 μF bypass capacitor should be connected between
the V
IN
pin and the GND pin.
3.8
Reference Voltage Input (V
REF
)
V
REF
is an external reference input pin used to regulate
the output of the power system. By changing the V
REF
input, the output (voltage or current) of the power sys-
tem can be changed. The reference voltage can range
from 0V to V
IN
(rail-to-rail).
DFN/MSOP
Name
Function
1
2
3
4
5
6
7
8
COMP
FB
CS
OSC IN
GND
V
EXT
V
IN
V
REF
Error Amplifier Output pin
Error Amplifier Inverting Input
Current Sense Input pin (MCP1630) or Voltage Ramp Input pin (MCP1630V)
Oscillator Input pin
Circuit Ground pin
External Driver Output pin
Input Bias pin
Reference Voltage Input pin
相關PDF資料 |
PDF描述 |
|---|---|
| MCP1650REUN | MCP1650 |
| MCP1650SEUN | MCP1650 |
| MCP1651REUN | MCP1650 |
| MCP1651SEUN | MCP1650 |
| MCP1652REUN | MCP1650 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP1630V-E/MC | 功能描述:電流型 PWM 控制器 Hi Spd PWM PIC atach RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MCP1630V-E/MS | 功能描述:電流型 PWM 控制器 High Speed PWM PIC attach RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MCP1630VT-E/MC | 功能描述:電流型 PWM 控制器 High Speed PWM PIC attach RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MCP1630VT-E/MS | 功能描述:電流型 PWM 控制器 High Speed PWM PIC attach RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MCP1631 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Speed, Pulse Width Modulator |
發布緊急采購，3分鐘左右您將得到回復。