- 您現在的位置：買賣IC網 > PDF目錄383586 > MCP1702 (Microchip Technology Inc.) 250 mA Low Quiescent Current LDO Regulator PDF資料下載
參數資料
| 型號： | MCP1702 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 250 mA Low Quiescent Current LDO Regulator |
| 中文描述： | 250毫安低靜態電流LDO穩壓器 |
| 文件頁數： | 10/26頁 |
| 文件大?。?/td> | 689K |
| 代理商： | MCP1702 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
MCP1702
DS22008B-page 10
2007 Microchip Technology Inc.
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE
3.1
Ground Terminal (GND)
Regulator ground. Tie GND to the negative side of the
output and the negative side of the input capacitor.
Only the LDO bias current (2.0 μA typical) flows out of
this pin; there is no high current. The LDO output
regulation is referenced to this pin. Minimize voltage
drops between this pin and the negative side of the
load.
3.2
Regulated Output Voltage (V
OUT
)
Connect V
OUT
to the positive side of the load and the
positive terminal of the output capacitor. The positive
side of the output capacitor should be physically
located as close to the LDO V
OUT
pin as is practical.
The current flowing out of this pin is equal to the DC
load current.
3.3
Unregulated Input Voltage Pin
(V
IN
)
Connect V
IN
to the input unregulated source voltage.
Like all LDO linear regulators, low source impedance is
necessary for the stable operation of the LDO. The
amount of capacitance required to ensure low source
impedance will depend on the proximity of the input
source capacitors or battery type. For most
applications, 1 μF of capacitance will ensure stable
operation of the LDO circuit. For applications that have
load currents below 100 mA, the input capacitance
requirement can be lowered. The type of capacitor
used can be ceramic, tantalum or aluminum
electrolytic. The low ESR characteristics of the ceramic
will yield better noise and PSRR performance at high-
frequency.
Pin No.
SOT-23A
Pin No.
SOT-89
Pin No.
TO-92
Symbol
Function
1
1
1
GND
Ground Terminal
2
3
3
V
OUT
V
IN
NC
Regulated Voltage Output
3
2, Tab
2
Unregulated Supply Voltage
–
–
–
No connection
相關PDF資料 |
PDF描述 |
|---|---|
| MCP1703 | 250 mA, 16V, Low Quiescent Current |
| MCP1725 | 500 mA, Low Voltage, Low Quiescent Current LDO Regulator |
| MCP1726 | 1A, Low Voltage, Low Quiescent Current LDO Regulator |
| MCP1727 | 1.5A, Low Voltage, Low Quiescent Current LDO Regulator |
| MCP1801 | 150 mA, High PSRR, Low Quiescent Current LDO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP1702-1202E/CB | 制造商:Microchip Technology Inc 功能描述: |
| MCP1702-1202E/TO | 功能描述:低壓差穩壓器 - LDO Low Iq 250mA LDO Vin 13.2V max Vout=1.2V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1702-1502E/TO | 功能描述:低壓差穩壓器 - LDO Low Iq 250mA LDO Vin 13.2V max Vout=1.5V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1702-1802E/TO | 功能描述:低壓差穩壓器 - LDO LDO w/ Low Quiescent RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1702-2502E/TO | 功能描述:低壓差穩壓器 - LDO LDO w/ Low Quiescent RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。