參數資料
型號： MCP1727
廠商： Microchip Technology Inc.
英文描述： 1.5A, Low Voltage, Low Quiescent Current LDO Regulator
中文描述： 1.5安培的電流，低電壓，低靜態電流LDO穩壓器
文件頁數： 18/32頁
文件大小： 678K
代理商： MCP1727
MCP1727
DS21999B-page 18
2007 Microchip Technology Inc.
Once the power good threshold (rising) has been
reached, the C
DELAY
pin charges the external capacitor
to V
IN
. The charging current is 140 nA (typical). The
PWRGD output will transition high when the C
DELAY
pin
voltage has charged to 0.42V. If the output falls below
the power good threshold limit during the charging time
between 0.0V and 0.42V on the C
DELAY
pin, the
C
DELAY
pin voltage will be pulled to ground, thus reset-
ting the timer. The C
DELAY
pin will be held low until the
output voltage of the LDO has once again risen above
the power good rising threshold. A timing diagram
showing C
DELAY
, PWRGD and V
OUT
is shown in
Figure 4-4
.
FIGURE 4-4:
Diagram.
C
DELAY
and PWRGD Timing
4.7
Shutdown Input (SHDN)
The SHDN input is an active-low input signal that turns
the LDO on and off. The SHDN threshold is a
percentage of the input voltage. The typical value of
this shutdown threshold is 30% of V
IN
, with minimum
and maximum limits over the entire operating
temperature range of 45% and 15%, respectively.
The SHDN input will ignore low-going pulses (pulses
meant to shut down the LDO) that are up to 400 ns in
pulse width. If the shutdown input is pulled low for more
than 400 ns, the LDO will enter Shutdown mode. This
small bit of filtering helps to reject any system noise
spikes on the shutdown input signal.
On the rising edge of the SHDN input, the shutdown
circuitry has a 30 μs delay before allowing the LDO
output to turn on. This delay helps to reject any false
turn-on signals or noise on the SHDN input signal. After
the 30 μs delay, the LDO output enters its soft-start
period as it rises from 0V to its final regulation value. If
the SHDN input signal is pulled low during the 30 μs
delay period, the timer will be reset and the delay time
will start over again on the next rising edge of the
SHDN input. The total time from the SHDN input going
high (turn-on) to the LDO output being in regulation is
typically 100 μs. See
Figure 4-5
for a timing diagram of
the SHDN input.
FIGURE 4-5:
Diagram.
Shutdown Input Timing
4.8
Dropout Voltage and Undervoltage
Lockout
Dropout voltage is defined as the input-to-output
voltage differential at which the output voltage drops
2% below the nominal value that was measured with a
V
R
+ 0.6V differential applied. The MCP1727 LDO has
a very low dropout voltage specification of 330 mV
(typical) at 1.5A of output current. See
Section 1.0
“Electrical Characteristics”
for maximum dropout
voltage specifications.
The MCP1727 LDO operates across an input voltage
range of 2.3V to 6.0V and incorporates input Undervolt-
age Lockout (UVLO) circuitry that keeps the LDO
output voltage off until the input voltage reaches a
minimum of 2.18V (typical) on the rising edge of the
input voltage. As the input voltage falls, the LDO output
will remain on until the input voltage level reaches
2.04V (typical).
Since the MCP1727 LDO undervoltage lockout
activates at 2.04V as the input voltage is falling, the
dropout voltage specification does not apply for output
voltages that are less than 1.9V.
For high-current applications, voltage drops across the
PCB traces must be taken into account. The trace
resistances can cause significant voltage drops
between the input voltage source and the LDO. For
applications with input voltages near 2.3V, these PCB
trace voltage drops can sometimes lower the input
voltage enough to trigger a shutdown due to
undervoltage lockout.
V
OUT
T
PG
V
PWRGD_TH
C
DELAY
C
DELAY
Threshold (0.42V)
PWRGD
0V
V
IN
(typ)
SHDN
V
OUT
30 μs
70 μs
T
OR
400 ns (typ)
相關PDF資料
PDF描述
MCP1801 150 mA, High PSRR, Low Quiescent Current LDO
MCP1802 300 mA, High PSRR, Low Quiescent Current LDO
MCP1827T-1202EAB 1.5A, Low Voltage, Low Quiescent Current LDO Regulator
MCP1827-5002EAB 1.5A, Low Voltage, Low Quiescent Current LDO Regulator
MCP1827-5002EAT 1.5A, Low Voltage, Low Quiescent Current LDO Regulator
相關代理商/技術參數
參數描述
MCP1727-0802E/MF 功能描述:低壓差穩壓器 - LDO 1.5A CMOS LDO .8V DFN8 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MCP1727-0802E/SN 功能描述:低壓差穩壓器 - LDO 1.5A Vout=0.8V Extended Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MCP1727-1202E/MF 功能描述:低壓差穩壓器 - LDO 1.5A CMOS LDO 1.2V DFN8 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MCP1727-1202E/SN 功能描述:低壓差穩壓器 - LDO 1.5A Vout=1.2V Extended Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MCP1727-1802E/MF 功能描述:低壓差穩壓器 - LDO 1.5A CMOS LDO 1.8V DFN8 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*