- 您現在的位置：買賣IC網 > PDF目錄10422 > MCP2022AT-500E/SL (Microchip Technology)IC TXRX LIN 5.0V LDO 14-SOIC PDF資料下載
參數資料
| 型號： | MCP2022AT-500E/SL |
| 廠商： | Microchip Technology |
| 文件頁數： | 23/48頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX LIN 5.0V LDO 14-SOIC |
| 產品培訓模塊： | Microchip MCP20xx LIN Transceiver Overview |
| 標準包裝： | 2,600 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
2012 Microchip Technology Inc.
DS22298A-page 3
MCP2021A/2A
1.0
FUNCTION DESCRIPTION
The MCP2021A/2A provides a physical interface
between a microcontroller and a LIN half-duplex bus. It
is intended for automotive and industrial applications
with serial bus baud rates up to 20 Kbaud. This device
will translate the CMOS/TTL logic levels to LIN logic
levels, and vice versa. The device offers optimum EMI
and ESD performance; it can withstand high voltage on
the LIN bus. The device supports two low-power
modes to meet automotive industry power consump-
tion requirements. The MCP2021A/2A also provides a
+5V or 3.3V 70 mA regulated power output.
1.1
Modes of Operation
The MCP2021A/2A works in five modes: POWER-ON-
RESET mode, POWER-DOWN mode, READY mode,
OPERATION mode, and TRANSMITTER OFF mode.
For an overview of all operational modes, please refer
to Table 1-1. For the operational mode transition,
please refer to Figure 1-1.
FIGURE 1-1:
STATE DIAGRAM
1.1.1
POWER-ON-RESET MODE
Upon application of VBB, or whenever the voltage on
VBB is below the threshold of regulator turn off voltage
VOFF (typically 4.50V), the device enters POWER-ON-
RESET mode (POR). During this mode, the device
maintains the digital section in a reset mode and waits
until the voltage on VBB pin rises above the threshold of
regulator turn on voltage VON (typically 5.75V) to enter
to the READY mode. In POWER-ON-RESET mode,
the LIN physical layer and voltage regulator are dis-
abled, and RESET output (MCP2022A only) is forced
to LOW.
POR
(2)
VREG OFF
RX OFF
TX OFF
READY
VREG ON
RX ON
TX OFF
TX OFF
VREG ON
RX ON
TX OFF
POWER-DOWN
VREG OFF
RX OFF
TX OFF
OPERATION
VREG ON
RX ON
TX ON
VBB>VON
CS/LWAKE=1&
FAULT/TXE=0&
VREG_OK=1
(1)
CS/LWAKE=0
CS/LWAKE=1 &
FAULT/TXE=1
(3) &
TXD=1&
VREG_OK=1
(1)
CS/LWAKE=1&
FAULT/TXE=1
(3)&
TXD=1
CS/LWAKE=1&
FAULT/TXE=0
CS/LWAKE=0
CS/LWAKE=1 OR
Voltage Rising Edge on LBUS
CS/LWAKE=0
Note 1: VREG_OK : Regulator Output Voltage > 0.8VREG_NOM.
2: If the voltage on pin VBB falls below VOFF, the device will enter POWER ON RESET mode from all other
modes, which is not shown in the figure.
3: FAULT/TXE = 1 represents input high and no fault conditions. FAULT/TXE = 0 represents input low or a
fault condition, Refer to Table 1-3.
相關PDF資料 |
PDF描述 |
|---|---|
| MCP2022AT-330E/SL | IC TXRX LIN 3.3V LDO 14-SOIC |
| MCP2022T-500E/SL | IC LIN TXRX ON-BOARD VREG 14SOIC |
| MCP2022-500E/SL | IC LIN TXRX W/V-REG 5V 14SOIC |
| MCP2022-500E/P | IC LIN TXRX ON-BOARD VREG 14DIP |
| MCP2021PT-500E/MD | IC TXRX LIN ON-BOARD VREG 8DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2022P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:LIN Transceiver with Voltage Regulator |
| MCP2022P-330E/SL | 功能描述:LIN 收發器 LIN Transceiver with Vreg and LIN RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MCP2022P-330E/ST | 功能描述:LIN 收發器 LIN Transceiver with Vreg and LIN RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MCP2022P-500E/SL | 功能描述:LIN 收發器 LIN Transceiver with Vreg and LIN RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MCP2022P-500E/ST | 功能描述:LIN 收發器 LIN Transceiver with Vreg and LIN RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
發布緊急采購，3分鐘左右您將得到回復。