- 您現在的位置：買賣IC網 > PDF目錄383588 > MCP2140 (Microchip Technology Inc.) IrDA Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate(固定波特率,低成本,IrDA標準協議編譯碼器) PDF資料下載
參數資料
| 型號： | MCP2140 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | IrDA Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate(固定波特率,低成本,IrDA標準協議編譯碼器) |
| 中文描述： | 標準的IrDA協議?？刂破?，固定通信速率9600波特（固定波特率，低成本，紅外標準協議編譯碼器） |
| 文件頁數： | 9/58頁 |
| 文件大小： | 1001K |
| 代理商： | MCP2140 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
2003 Microchip Technology Inc.
Preliminary
DS21790A-page 9
MCP2140
2.4
Host UART Interface
The Host UART interface communicates with the Host
Controller. This interface has eight signals associated
with it: TX, RX, RTS, CTS, DSR, DTR, CD and RI. Sev-
eral of these signals are locally generated (not passed
over the IR interface). The Host UART is a half-duplex
interface, meaning that the system is either transmitting
or receiving, but not both simultaneously.
2.4.1
BAUD RATE
The baud rate for the MCP2140 serial port (the TX and
RX pins) is fixed at 9600 baud when the device
frequency is 7.3728 MHz.
2.4.2
TRANSMITTING
When the controller sends serial data to the MCP2140,
the controller’s baud rate is required to match the baud
rate of the MCP2140’s serial port.
2.4.3
RECEIVING
When the controller receives serial data from the
MCP2140, the controller’s baud rate is required to
match the baud rate of the MCP2140’s serial port.
2.4.4
HARDWARE HANDSHAKING
There are three Host UART signals used to control the
handshaking operation between the Host Controller
and the MCP2140. They are:
DSR
RTS
CTS
2.4.4.1
DSR
The DSR signal is used to indicate that a link has been
established between the MCP2140 and the Primary
Device. Please refer to Section 2.13, “How Devices
Connect”, for information on how devices connect.
2.4.4.2
RTS
The RTS signal indicates to the MCP2140 that the Host
Controller is ready to receive serial data. Once an IR
data packet has been received, the RTS signal will be
low for the received data to be transferred to the Host
Controller. If the RTS signal remains high, an IR link
timeout will occur and the MCP2140 will disconnect
from the Primary Device.
2.4.4.3
CTS
The MCP2140 generates the CTS signal locally due to
buffer limitations.
The MCP2140 uses a 64-byte buffer for incoming data
from the IR Host. Another 29-byte buffer is provided to
buffer data from the UART serial port. The MCP2140
can handle IR data and Host UART serial port data
simultaneously. A hardware handshaking pin (CTS) is
provided to inhibit the Host Controller from sending
serial data when the Host UART buffer is not available
(Figure 2-3). Figure 2-4 shows a flow chart for Host
UART flow control using the CTS signal.
FIGURE 2-3:
HOST UART CTS SIGNAL AND THE RECEIVE BUFFER
Note 1:
The MCP2140 generates several non-
data signals locally.
2:
The MCP2140 emulates a 3-wire serial
connection (TXD, RXD and GND). The
transceiver’s
Transmit
Receive Data (RXD) signals, and the
state of the CD. RI and DTR input pins
are carried back and forth to the Primary
device.
Data
(TXD),
3:
The RTS and CTS signals are local
emulations.
Note:
When the CTS output signal goes high, the
UART FIFO will store up to 6 bytes. This is
to allow devices that have a slow response
time to a change on the CTS signal time to
stop sending additional data (such as a
modem).
CTS
Receive Buffer Empty
MCP2140
Can Receive Data Receive Buffer Has 22 Bytes,
CTS Pin Driven High
Receive Buffer
Full (29 Bytes)
Receive Buffer Empty
MCP2140
Can Receive Data
IR Data Packet Starts Transmission
IR Data Packet Transmitted
相關PDF資料 |
PDF描述 |
|---|---|
| MCP2150 | DEVELOPER’S KIT USER’S GUIDE |
| MCP2155 | IrDA Standard Protocol Stack Controller Supporting DCE Applications(提供IrDA協議來處理PLUS位的編碼/譯碼功能,這是為了在一個低引腳的計數設備上實現數據傳輸功能(DCE)而提供的) |
| MCP23016 | 16-Bit I2C I/O Expander(16位I/O口擴展芯片) |
| MCP3008(中文) | 2.7V 4-Channel/8-Channel 10-Bit A/D Converters With SPI Serial Interface(2.7V，4通道/8通道，10位，帶SPI串口的A/D轉換器) |
| MCP3004(中文) | 2.7V 4-Channel/8-Channel 10-Bit A/D Converters With SPI Serial Interface(2.7V，4通道/8通道，10位，帶SPI串口的A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2140_03 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:IrDA㈢ Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate |
| MCP2140_13 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:IrDA?? Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate |
| MCP2140A | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:IrDA㈢ Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate |
| MCP2140A-I/P | 功能描述:網絡控制器與處理器 IC Enhanced MCP2140 Win Mobile 5.0 compatble RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCP2140A-I/SO | 功能描述:網絡控制器與處理器 IC Enhanced MCP2140 Win Mobile 5.0 compatble RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。