參數資料
型號: MCP2140T-I/SS
廠商: Microchip Technology
文件頁數: 56/58頁
文件大?。?/td> 0K
描述: IC IRDA CONTROLLR DTE/DCE 20SSOP
標準包裝: 1,600
控制器類型: IRDA 標準協議??刂破?br>
接口: UART
電源電壓: 3 V ~ 5.5 V
電流 - 電源: 2.2mA
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 20-SSOP(0.209",5.30mm 寬)
供應商設備封裝: 20-SSOP
包裝: 帶卷 (TR)
配用: MCP2140DM-TMPSNS-ND - BOARD DEMO FOR MCP2140
2003 Microchip Technology Inc.
Preliminary
DS21790A-page 7
MCP2140
2.0
DEVICE OPERATION
The MCP2140 serial interface and IR baud rates are
fixed at 9600 baud, given a 7.3728 MHz device clock.
2.1
Power-Up
Any time the device is powered up (Parameter D003),
the Power-Up Timer delay (Parameter 33) occurs, fol-
lowed by an Oscillator Start-up Timer (OST) delay
(Parameter 32). Once these delays complete, commu-
nication with the device may be initiated. This commu-
nication is from both the infrared transceiver’s side and
the controller’s UART interface.
2.2
Device Reset
The MCP2140 is forced into the reset state when the
RESET pin is in the low state. Once the RESET pin is
brought to a high state, the Device Reset sequence
occurs. Once the sequence completes, functional
operation begins.
2.3
Device Clocks
The MCP2140 requires a clock source to operate. This
clock source is used to establish the device timing,
including the device “Bit Clock”.
2.3.1
CLOCK SOURCE
The clock source can be supplied by one of the
following:
Crystal
Resonator
External clock
The frequency of this clock source must be
7.3728 MHz (electrical specification Parameter 1A) for
device communication at 9600 baud.
2.3.1.1
Crystal Oscillator / Ceramic
Resonators
A crystal or ceramic resonator can be connected to the
OSC1 and OSC2 pins to establish oscillation
(Figure 2-1). The MCP2140 oscillator design requires
the use of a parallel-cut crystal. Use of a series of cut
crystals may give a frequency outside of the crystal
manufacturers specifications.
FIGURE 2-1:
CRYSTAL OPERATION
(CERAMIC RESONATOR)
TABLE 2-1:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
TABLE 2-2:
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
Freq
OSC1 (C1)
OSC2 (C2)
7.3728 MHz
10 - 22 pF
Note:
Higher capacitance increases the stability
of the oscillator, but also increases the
start-up time. These values are for design
guidance only. Since each resonator has its
own characteristics, the user should consult
the resonator manufacturer for appropriate
values of external components.
Freq
OSC1 (C1)
OSC2 (C2)
7.3728 MHz
15 - 30 pF
Note:
Higher capacitance increases the stability
of the oscillator but also increases the start-
up time. These values are for design guid-
ance only. RS may be required to avoid
overdriving crystals with low drive level
specification. Since each crystal has its
own characteristics, the user should con-
sult
the
crystal
manufacturer
for
appropriate values of external components.
See Table 2-1 and Table 2-2 for recommended
values of C1 and C2.
Note:
A series resistor may be required for
AT strip cut crystals.
C1
C2
XTAL
OSC2
RS
OSC1
RF
To internal
MCP2140
(Note)
logic
相關PDF資料
PDF描述
MCP2140AT-I/SS IC IRDA CONTROLLR DTE/DCE 20SSOP
V150A15C400BF2 CONVERTER MOD DC/DC 15V 400W
V150A15C400BF CONVERTER MOD DC/DC 15V 400W
MCP2515-E/SO IC CAN CONTROLLER W/SPI 18SOIC
PIC12LCE519-04I/P IC MCU OTP 1KX12 LV W/EE 8DIP
相關代理商/技術參數
參數描述
MCP2150 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:DEVELOPER’S KIT USER’S GUIDE
MCP2150_13 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:IrDA?? Standard Protocol Stack Controller Supporting DTE Applications
MCP2150DM 功能描述:界面開發工具 MCP2150 Dev Board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
MCP2150-I/P 功能描述:輸入/輸出控制器接口集成電路 IrDA protocol handlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
MCP2150-I/P 制造商:Microchip Technology Inc 功能描述:IC IRDA CONTROLLER 2150 DIP18