- 您現在的位置：買賣IC網 > PDF目錄3773 > MCP23S18-E/SO (Microchip Technology)IC I/O EXPANDER SPI 16B 28SOIC PDF資料下載
參數資料
| 型號： | MCP23S18-E/SO |
| 廠商： | Microchip Technology |
| 文件頁數： | 2/56頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER SPI 16B 28SOIC |
| 標準包裝： | 27 |
| 接口： | SPI |
| 輸入/輸出數： | 16 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 10MHz |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 684 (CN2011-ZH PDF) |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
MCP23018/MCP23S18
DS22103A-page 10
2008 Microchip Technology Inc.
1.4
Multi-bit Address Decoder
The ADDR pin is used to set the slave address of the
MCP23018 (I2C only) to allow up to eight devices on
the bus using only a single pin. Typically, this would
require three pins.
The multi-bit Address Decoder employs a basic FLASH
ADC architecture (Figure 1-4). The seven comparators
generate 8 unique values based on the analog input.
This value is converted to a 3-bit code which corre-
sponds to the address bits (A2, A1, A0) in the serial
OPCODE.
Sequence
of
Operation
(see
for
timings):
1.
Upon power up (after VDD stabilizes) the module
becomes active after time tADEN. Note, the ana-
log value on the ADDR pin must be stable
before this point to ensure accurate address
assignment.
2.
The 3-bit address is latched after tADDRLAT.
3.
The module powers down after the first rising
edge of the serial clock is detected (tADDIS).
Once the address bits are latched, the device will keep
the slave address until a POR or reset condition
occurs.
1.4.1
CALCULATING VOLTAGE ON ADDR
When calculating the required voltage on the ADDR pin
(V2), the set point should be the mid-point of the LSb of
the ADC.
The examples in Figure 1-2 and Figure 1-3 show how
to determine the mid point voltage (V2) and the range
of voltages based on a voltage divider circuit. The
maximum tolerance is 20%, however, it is recom-
mended to use 5% tolerance worst case (10% total tol-
erance).
FIGURE 1-2:
VOLTAGE DIVIDER EXAMPLE
R2
A0
A1
A2
V2
R1
VDD
MCP23018
VDD
VSS
ADDR
相關PDF資料 |
PDF描述 |
|---|---|
| MCP23016-I/SP | IC I/O EXPANDER I2C 16B 28SDIP |
| MCP23018-E/MJ | IC I/O EXPANDER I2C 16B 24QFN |
| MCP23009-E/MG | IC I/O EXPANDER I2C 8B 16QFN |
| MCP23018-E/SO | IC I/O EXPANDER I2C 16B 28SOIC |
| MCP23018-E/SP | IC I/O EXPANDER I2C 16B 28SDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP23S18T | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16-Bit I/O Expander with Open-Drain Outputs |
| MCP23S18T-E/MJ | 功能描述:接口-I/O擴展器 16B I/O Expander SPI interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23S18T-E/SO | 功能描述:接口-I/O擴展器 16B I/O Expander SPI interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23S18T-E/SP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16-Bit I/O Expander with Open-Drain Outputs |
| MCP23S18T-E/SS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16-Bit I/O Expander with Open-Drain Outputs |
發布緊急采購，3分鐘左右您將得到回復。