參數資料
型號: MCP2510-E/SO
元件分類: 微控制器/微處理器
英文描述: 1 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDSO18
封裝: 0.300 INCH, PLASTIC, SOIC-18
文件頁數: 8/80頁
文件大小: 998K
代理商: MCP2510-E/SO
MCP2510
DS21291F-page 16
2007 Microchip Technology Inc.
Only messages that have not already begun to be
transmitted can be aborted. Once a message has
begun transmission, it will not be possible for the user
to reset the TXBnCTRL.TXREQ bit. After transmission
of a message has begun, if an error occurs on the bus
or if the message loses arbitration, the message will be
retransmitted regardless of a request to abort.
FIGURE 3-1:
TRANSMIT MESSAGE FLOWCHART
Start
Is
CAN Bus available
to start transmission
No
Examine TXBnCTRL.TXP <1:0> to
Are any
TXBnCTRL.TXREQ
?
bits = 1
The
message
transmission
sequence begins when the
device determines that the
TXBnCTRL.TXREQ for any of
the transmit registers has been
set.
Clear:
TXBnCTRL.ABTF
TXBnCTRL.MLOA
TXBnCTRL.TXERR
Yes
?
is
TXBnCTRL.TXREQ=0
CANCTRL.ABAT=1
Clearing the TxBnCTRL.TXREQ
bit while it is set, or setting the
CANCTRL.ABAT bit before the
message has started transmission
will abort the message.
No
Transmit Message
Was
Message Transmitted
Successfully?
No
Yes
Set TxBnCTRL.TXREQ=0
CANINTE.TXnIE=1?
Generate
Interrupt
Yes
Set
Did
a message error
occur?
Was
Arbitration lost during
transmission?
Set
TxBnCTRL.TXERR=1
Yes
No
Determine Highest Priority Message
No
?
TxBnCTRL.MLOA=1
The CANINTE.TXnIE bit
determines if an interrupt
should be generated when
a message is successfully
transmitted.
GOTO START
CANTINF.TXnIF=1
Yes
No
相關PDF資料
PDF描述
MCP2510T-I/SOA32 1 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDSO18
MCP2510T-I/SOA01 1 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDSO18
MCP2510-I/STVAO 1 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDSO20
MCP2510T-I/SO 1 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDSO18
MCP2510-I/STG 1 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDSO20
相關代理商/技術參數
參數描述
MCP2510-EST 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI Interface
MCP2510-I/P 功能描述:網絡控制器與處理器 IC Stand-alone CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCP2510-I/P 制造商:Microchip Technology Inc 功能描述:IC CAN CONTROLLER 2510 DIP18
MCP2510-I/SO 功能描述:網絡控制器與處理器 IC Stand-alone CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCP2510-I/SO 制造商:Microchip Technology Inc 功能描述:IC CAN CONTROLLER 2510 SOIC18