參數資料
型號： MCP2515T-I/ML
元件分類： 微控制器/微處理器
英文描述： 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC20
封裝： 4 X 4 MM, 0.90 MM HEIGHT, LEAD FREE, PLASTIC, QFN-20
文件頁數： 54/88頁
文件大?。?/td> 1205K
代理商： MCP2515T-I/ML
MCP2515
DS21801F-page 58
2010 Microchip Technology Inc.
10.4
Loopback Mode
Loopback mode will allow internal transmission of
messages from the transmit buffers to the receive
buffers without actually transmitting messages on the
CAN bus. This mode can be used in system
development and testing.
In this mode, the ACK bit is ignored and the device will
allow incoming messages from itself just as if they were
coming from another node. The Loopback mode is a
silent mode, meaning no messages will be transmitted
while in this state (including error flags or acknowledge
signals). The TXCAN pin will be in a recessive state.
The filters and masks can be used to allow only
particular messages to be loaded into the receive
registers. The masks can be set to all zeros to provide
a mode that accepts all messages. The Loopback
mode is activated by setting the mode request bits in
the CANCTRL register.
10.5
Normal Mode
Normal mode is the standard operating mode of the
MCP2515. In this mode, the device actively monitors all
bus messages and generates acknowledge bits, error
frames, etc. This is also the only mode in which the
MCP2515 will transmit messages over the CAN bus.
REGISTER 10-1:
CANCTRL – CAN CONTROL REGISTER
(ADDRESS: XFh)
R/W-1
R/W-0
R/W-1
REQOP2
REQOP1
REQOP0
ABAT
OSM
CLKEN
CLKPRE1
CLKPRE0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-5
REQOP: Request Operation Mode bits <2:0>
000
=
Set Normal Operation mode
001
=
Set Sleep mode
010
=
Set Loopback mode
011
=
Set Listen-only mode
100
=
Set Configuration mode
All other values for REQOP bits are invalid and should not be used
On power-up, REQOP = b’111’
bit 4
ABAT: Abort All Pending Transmissions bit
1
= Request abort of all pending transmit buffers
0
= Terminate request to abort all transmissions
bit 3
OSM: One Shot Mode bit
1
= Enabled. Message will only attempt to transmit one time
0
= Disabled. Messages will reattempt transmission, if required
bit 2
CLKEN: CLKOUT Pin Enable bit
1
= CLKOUT pin enabled
0
= CLKOUT pin disabled (Pin is in high-impedance state)
bit 1-0
CLKPRE: CLKOUT Pin Prescaler bits <1:0>
00
=FCLKOUT = System Clock/1
01
=FCLKOUT = System Clock/2
10
=FCLKOUT = System Clock/4
11
=FCLKOUT = System Clock/8
相關PDF資料
PDF描述
MCP2515T-I/SO 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDSO18
MCP2515-E/ST 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDSO20
MCP2515T-E/ST 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDSO20
MCP2515T-E/ML 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC20
MCP2515-E/PG 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDIP18
相關代理商/技術參數
參數描述
MCP2551 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Speed CAN Transceiver
MCP2551_07 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Speed CAN Transceiver
MCP2551_10 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Speed CAN Transceiver
MCP2551A-E/P 功能描述:CAN 接口集成電路 Enhanced HI SPD CAN Transceiver RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MCP2551A-E/SN 功能描述:CAN 接口集成電路 Enhanced HI SPD CAN Transceiver RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*