參數資料
型號： MCP2515T-I/ML
廠商： Microchip Technology
文件頁數： 17/88頁
文件大?。?/td> 0K
描述： IC CAN CTLR W/SPI 2.0B 20-QFN
標準包裝： 1
控制器類型： CAN 接口
接口： SPI 串行
電源電壓： 2.7 V ~ 5.5 V
電流 - 電源： 10mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 20-VFQFN 裸露焊盤
供應商設備封裝： 20-QFN 裸露焊盤（4x4）
包裝： 標準包裝
其它名稱： MCP2515T-I/MLDKR
MCP2515
DS21801F-page 24
2010 Microchip Technology Inc.
4.3
Start-of-Frame Signal
If enabled, the Start-Of-Frame signal is generated on
the SOF pin at the beginning of each CAN message
detected on the RXCAN pin.
The RXCAN pin monitors an idle bus for a recessive-
to-dominant edge. If the dominant condition remains
until the sample point, the DSTEMP interprets this as a
SOF and a SOF pulse is generated. If the dominant
condition does not remain until the sample point, the
DSTEMP interprets this as a glitch on the bus and no
SOF signal is generated. Figure 4-1 illustrates SOF
signalling and glitch-filtering.
As with One-shot mode, one use for SOF signaling is
for TTCAN-type systems. In addition, by monitoring
both the RXCAN pin and the SOF pin, an MCU can
detect early physical bus problems by detecting small
glitches before they affect the CAN communications.
4.4
RX0BF and RX1BF Pins
In addition to the INT pin, which provides an interrupt
signal to the MCU for many different conditions, the
receive buffer full pins (RX0BF and RX1BF) can be
used to indicate that a valid message has been loaded
into RXB0 or RXB1, respectively. The pins have three
different configurations (Register 4-1):
1.
Disabled
2.
Buffer Full Interrupt
3.
Digital Output
4.4.1
DISABLED
The RXBnBF pins can be disabled to the high-
impedance state by clearing BFPCTRL.BnBFE.
4.4.2
CONFIGURED AS BUFFER FULL
The RXBnBF pins can be configured to act as either
buffer full interrupt pins or as standard digital outputs.
Configuration and status of these pins is available via
the BFPCTRL register (Register 4-3). When set to
operate in Interrupt mode (by setting BFPCTRL.BxBFE
and BFPCTRL.BxBFM bits), these pins are active-low
and are mapped to the CANINTF.RXnIF bit for each
receive buffer. When this bit goes high for one of the
receive buffers (indicating that a valid message has
been loaded into the buffer), the corresponding
RXBnBF pin will go low. When the CANINTF.RXnIF bit
is cleared by the MCU, the corresponding interrupt pin
will go to the logic-high state until the next message is
loaded into the receive buffer.
FIGURE 4-1:
START-OF-FRAME SIGNALING
START-OF-FRAME BIT
Sample
Point
ID BIT
RXCAN
SOF
EXPECTED START-OF-FRAME BIT
Sample
Point
BUS IDLE
RXCAN
SOF
Expected
Normal SOF Signaling
Glitch-Filtering
相關PDF資料
PDF描述
PIC16F1825T-I/ML MCU PIC 14K FLASH 1K RAM 16QFN
PIC16F1828T-I/SS IC MCU 8BIT 7KB FLASH 20SSOP
PIC16LF1828T-I/SS IC MCU 8BIT 7KB FLASH 20SSOP
PIC16LF1824-E/P IC MCU 8BIT 7KB FLASH 14PDIP
PIC16F1824-E/P IC MCU 8BIT 7KB FLASH 14PDIP
相關代理商/技術參數
參數描述
MCP2551 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Speed CAN Transceiver
MCP2551_07 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Speed CAN Transceiver
MCP2551_10 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Speed CAN Transceiver
MCP2551A-E/P 功能描述:CAN 接口集成電路 Enhanced HI SPD CAN Transceiver RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MCP2551A-E/SN 功能描述:CAN 接口集成電路 Enhanced HI SPD CAN Transceiver RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*