- 您現在的位置：買賣IC網 > PDF目錄383588 > MCP3201-BIST (Microchip Technology Inc.) 2.7V 12-Bit A/D Converter with SPI Serial Interface PDF資料下載
參數資料
| 型號： | MCP3201-BIST |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 2.7V 12-Bit A/D Converter with SPI Serial Interface |
| 中文描述： | 2.7 12位A / D轉換器具有SPI串行接口 |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 377K |
| 代理商： | MCP3201-BIST |
MCP3201
DS21290B-page 16
Preliminary
1999 Microchip Technology Inc.
6.2
Maintaining Minimum Clock Speed
When the MCP3201 initiates the sample period,
charge is stored on the sample capacitor. When the
sample period is complete, the device converts one bit
for each clock that is received. It is important for the
user to note that a slow clock rate will allow charge to
bleed off the sample cap while the conversion is taking
place. At 85°C (worst case condition), the part will
maintain proper charge on the sample capacitor for at
least 1.2ms after the sample period has ended. This
means that the time between the end of the sample
period and the time that all 12 data bits have been
clocked out must not exceed 1.2ms (effective clock fre-
quency of 10kHz). Failure to meet this criteria may
induce linearity errors into the conversion outside the
rated specifications. It should be noted that during the
entire conversion cycle, the A/D Converter does not
require a constant clock speed or duty cycle, as long as
all timing specifications are met.
6.3
Buffering/Filtering the Analog Inputs
If the signal source for the A/D Converter is not a low
impedance source, it will have to be buffered or inaccu-
rate conversion results may occur. See Figure 4-2. It is
also recommended that a filter be used to eliminate any
signals that may be aliased back into the conversion
results. This is illustrated in Figure 6-3 where an op
amp is used to drive the analog input of the MCP3201.
This amplifier provides a low impedance source for the
converter input and a low pass filter, which eliminates
unwanted high frequency noise.
Low pass (anti-aliasing) filters can be designed using
Microchip’s interactive
FilterLab
software.
FilterLab
will calculate capacitor and resistor values, as well as
determine the number of poles that are required for the
application. For more information on filtering signals,
see the application note AN699
“Anti-Aliasing Analog
Filters for Data Acquisition Systems.”
FIGURE 6-3:
used to implement a 2nd order anti-aliasing filter for
the signal being converted by the MCP3201.
The MCP601 Operational Amplifier is
6.4
Layout Considerations
When laying out a printed circuit board for use with ana-
log components, care should be taken to reduce noise
wherever possible. A bypass capacitor should always
be used with this device and should be placed as close
as possible to the device pin. A bypass capacitor value
of 1μF is recommended.
Digital and analog traces should be separated as much
as possible on the board and no traces should run
underneath the device or the bypass capacitor. Extra
precautions should be taken to keep traces with high
frequency signals (such as clock lines) as far as possi-
ble from analog traces.
Use of an analog ground plane is recommended in
order to keep the ground potential the same for all
devices on the board. Providing V
DD
connections to
devices in a “star” configuration can also reduce noise
by eliminating current return paths and associated
errors. See Figure 6-4. For more information on layout
tips when using A/D Converter, refer to AN688 “Layout
Tips for 12-Bit A/D Converter Applications”
.
FIGURE 6-4:
configuration in order to reduce errors caused by
current return paths.
V
DD
traces arranged in a ‘Star’
FilterLab is a trademark of Microchip Technology Inc. in
the U.S.A and other countries. All rights reserved.
MCP3201
V
DD
10
μF
IN-
IN+
-
+
V
IN
C
1
C
2
V
REF
4.096V
Reference
0.1μF
ADI
REF198
1μF
1μF
0.1μF
MCP601
R
1
R
2
R
3
R
4
V
Connection
Device 1
Device 2
Device 3
Device 4
相關PDF資料 |
PDF描述 |
|---|---|
| MCP3201-CISN | 2.7V 12-Bit A/D Converter with SPI Serial Interface |
| mcp3201 | 2.7V 12-Bit A/D Converter with SPI Serial Interface(SPI接口的12位A/D轉換器) |
| MCP3202-BIP | 2.7V Dual Channel 12-Bit A/D Converter with SPI Serial Interface |
| MCP3202-CIST | 2.7V Dual Channel 12-Bit A/D Converter with SPI Serial Interface |
| MCP3202-BISN | 2.7V Dual Channel 12-Bit A/D Converter with SPI Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3201-CI/MS | 功能描述:模數轉換器 - ADC 12-bit SPI Sgl Chl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3201-CI/P | 功能描述:模數轉換器 - ADC 12-bit SPI Sgl Chl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3201-CI/P | 制造商:Microchip Technology Inc 功能描述:IC 12BIT ADC 3201 DIP8 |
| MCP3201-CI/SN | 功能描述:模數轉換器 - ADC 12-bit SPI Sgl Chl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3201-CI/SN | 制造商:Microchip Technology Inc 功能描述:IC 12BIT ADC SMD 3201 SOIC8 |
發布緊急采購，3分鐘左右您將得到回復。