參數資料
型號： MCP4019T-103E/LT
廠商： Microchip Technology
文件頁數： 39/51頁
文件大小： 0K
描述： IC DGTL POT 10K 128TAPS SC70-5
標準包裝： 1
接片： 128
電阻（歐姆）： 10k
電路數： 1
溫度系數： 標準值 150 ppm/°C
存儲器類型： 易失
接口： I²C
電源電壓： 1.8 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 6-TSSOP（5 引線），SC-88A，SOT-353
供應商設備封裝： SC-70-5
包裝： 標準包裝
產品目錄頁面： 674 (CN2011-ZH PDF)
其它名稱： MCP4019T-103E/LTDKR
MCP4017/18/19
DS22147A-page 44
2009 Microchip Technology Inc.
6.3
Wiper Resistance
Wiper resistance is the series resistance of the analog
switch that connects the selected resistor ladder node
to the Wiper Terminal common signal (see Figure 6-1).
A value in the volatile wiper register selects which
analog switch to close, connecting the W terminal to
the selected node of the resistor ladder.
The resistance is dependent on the voltages on the
analog switch source, gate, and drain nodes, as well as
the device’s wiper code, temperature, and the current
through the switch. As the device voltage decreases,
the wiper resistance increases (see Figure 6-4 and
The wiper can connect directly to Terminal B or to
Terminal A. A zero scale connections, connects the
Terminal W (wiper) to Terminal B (wiper setting of
000h). A full scale connections, connects the Terminal
W (wiper) to Terminal A (wiper setting of 7Fh). In these
configurations the only resistance between the
Terminal W and the other Terminal (A or B) is that of the
analog switches.
The wiper resistance is typically measured when the
wiper is positioned at either zero scale (00h) or full
scale (3Fh).
The wiper resistance in potentiometer-generated
voltage divider applications is not a significant source
of error.
The wiper resistance in rheostat applications can
create significant nonlinearity as the wiper is moved
toward zero scale (00h). The lower the nominal
resistance, the greater the possible error.
In a rheostat configuration, this change in voltage
needs to be taken into account. Particularly for the
lower resistance devices. For the 5.0 k
Ω device the
maximum wiper resistance at 5.5V is approximately
3.2% of the total resistance, while at 2.7V it is
approximately 6.5% of the total resistance.
In a potentiometer configuration, the wiper resistance
variation does not effect the output voltage seen on the
W pin.
The slope of the resistance has a linear area (at the
higher voltages) and a non-linear area (at the lower
voltages). In where resistance increases faster then the
voltage drop (at low voltages).
FIGURE 6-4:
Relationship of Wiper
Resistance (RW) to Voltage.
Since there is minimal variation of the total device
resistance over voltage, at a constant temperature (see
the change in wiper resistance over voltage can have a
significant impact on the INL and DNL error.
TABLE 6-4:
TYPICAL STEP RESISTANCES AND RELATIONSHIP TO WIPER RESISTANCE
RW
VDD
Note: The slope of the resistance has a linear
area (at the higher voltages) and a
non-linear area (at the lower voltages).
Resistance (
Ω)RW / RS (%) (1)
RW / RAB (%) (2)
Typical
Wiper (RW)
RW =
Typical
RW = Max
@ 5.5V
RW = Max
@ 2.7V
RW =
Typical
RW = Max
@ 5.5V
RW = Max
@ 2.7V
Total
(RAB)
Step
(RS)
Typical
Max @
5.5V
Max @
2.7V
5000
39.37
100
170
325
254.00%
431.80%
825.5%
2.00%
3.40%
6.50%
10000
78.74
100
170
325
127.00%
215.90%
412.75%
1.00%
1.70%
3.25%
50000
393.70
100
170
325
25.40%
43.18%
82.55%
0.20%
0.34%
0.65%
100000
787.40
100
170
325
12.70%
21.59%
41.28%
0.10%
0.17%
0.325%
Note 1: RS is the typical value. The variation of this resistance is minimal over voltage.
2: RAB is the typical value. The variation of this resistance is minimal over voltage.
相關PDF資料
PDF描述
MCP4021T-502E/MC IC DGTL POT 5K 1CH 8DFN
MCP40D18T-503AE/LT IC POT 7BIT 50K I2C SC-70-6
MCP42100T-E/ST IC POT DGTL 100K 2CH SPI 14TSSOP
MCP4251-503E/P IC DGTL POT 50K 2CH 14DIP
MCP4261-104E/P IC POT DGTL DUAL 100K SPI 14DIP
相關代理商/技術參數
參數描述
MCP4019T-104E/LT 功能描述:數字電位計 IC 100K I2C singl 7-bit volatile memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP4019T-502E/LT 功能描述:數字電位計 IC 5K I2C single 7-bit volatile memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP4019T-503E/LT 功能描述:數字電位計 IC 50K I2C single 7-bit volatile memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP401XEV 功能描述:數字電位計開發工具 MCP401X Evaluation Board RoHS:否 制造商:Arduino 產品:TinkerKit Rotary Potentiometers 工具用于評估:TinkerKit 電阻:4.7 kOhms 工作電源電壓:0 V to 5 V
MCP4021 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low-Cost NV Digital POT with WiperLock⑩ Technology
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*