參數資料
型號: MCP4441-104E/ST
廠商: Microchip Technology
文件頁數: 55/100頁
文件大?。?/td> 0K
描述: IC DGTL POT 129TAPS QUAD 20TSSOP
標準包裝: 74
接片: 129
電阻(歐姆): 100k
電路數: 4
溫度系數: 標準值 150 ppm/°C
存儲器類型: 非易失
接口: I²C(設備位址)
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 20-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 20-TSSOP
包裝: 管件
MCP444X/446X
DS22265A-page 58
2010 Microchip Technology Inc.
6.2.7
GENERAL CALL
The General Call is a method that the “Master” device
can communicate with all other “Slave” devices. In a
Multi-Master application, the other Master devices are
operating in Slave mode. The General Call address
has two documented formats. These are shown in
Figure 6-11. We have added a MCP44XX format in this
figure as well.
This will allow customers to have multiple I2C Digital
Potentiometers on the bus and have them operate in a
synchronous fashion (analogous to the DAC Sync pin
functionality). If these MCP44XX 7-bit commands
conflict with other I2C devices on the bus, then the
customer will need two I2C busses and ensure that the
devices are on the correct bus for their desired
application functionality.
Dual Pot devices can not update both Pot0 and Pot1
from a single command. To address this, there are
General Call commands for the Wiper 0, Wiper 1, and
the TCON registers.
Table 6-3 shows the General Call Commands. Three
commands are specified by the I2C specification and
are not applicable to the MCP44XX (so command is
Not Acknowledged) The MCP44XX General Call
Commands are Acknowledge. Any other command is
Not Acknowledged.
TABLE 6-3:
GENERAL CALL COMMANDS
Note:
Only one General Call command per issue
of the General Call control byte. Any
additional General Call commands are
ignored and Not Acknowledged.
7-bit
Command
(1, 2, 3)
Comment
‘1000 00d’b Write Next Byte (Third Byte) to Volatile
Wiper 0 Register
‘1001 00d’b Write Next Byte (Third Byte) to Volatile
Wiper 1 Register
‘1100 00d’b Write Next Byte (Third Byte) to TCON
Register
‘1000 010’b
or
‘1000 011’b
Increment Wiper 0 Register
‘1001 010’b
or
‘1001 011’b
Increment Wiper 1 Register
‘1000 100’b
or
‘1000 101’b
Decrement Wiper 0 Register
‘1001 100’b
or
‘1001 101’b
Decrement Wiper 1 Register
Note 1:
Any other code is Not Acknowledged.
These codes may be used by other
devices on the I2C bus.
2:
The 7-bit command always appends a “0”
to form 8-bits.
3:
“d” is the D8 bit for the 9-bit write value.
相關PDF資料
PDF描述
MS3110J12-10S CONN RCPT 10POS WALL MNT W/SCKT
VI-2NY-MW-F3 CONVERTER MOD DC/DC 3.3V 66W
VI-21N-MX-B1 CONVERTER MOD DC/DC 18.5V 75W
D38999/20WE8PN CONN RCPT 8POS WALL MNT W/PINS
MS3101E32-76S CONN RCPT 19POS FREE HNG W/SCKT
相關代理商/技術參數
參數描述
MCP4441-502E/ML 功能描述:數字電位計 IC 5k I2C Quad Ch 7bit Nonvolatile Memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP4441-502E/ML 制造商:Microchip Technology Inc 功能描述:; End To End Resistance:5kohm; Track Tap 制造商:Microchip Technology Inc 功能描述:IC, DIG POT, 5kohm, 129STEPS, QUAD, QFN-20
MCP4441-502E/ST 功能描述:數字電位計 IC 5k I2C Quad Ch 7bit Nonvolatile Memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP4441-502E/ST 制造商:Microchip Technology Inc 功能描述:; End To End Resistance:5kohm; Track Tap 制造商:Microchip Technology Inc 功能描述:IC, DIG POT, 5kohm, 129STEPS, QUAD, TSSOP-20
MCP4441-503E/ML 功能描述:數字電位計 IC 50k I2C Quad Ch 7bit Nonvolatile Memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel