參數資料
型號: MCP4441T-503E/ML
廠商: Microchip Technology
文件頁數: 94/100頁
文件大小: 0K
描述: IC DGTL POT 129TAPS QUAD 20QFN
標準包裝: 3,300
接片: 129
電阻(歐姆): 50k
電路數: 4
溫度系數: 標準值 150 ppm/°C
存儲器類型: 非易失
接口: I²C(設備位址)
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 20-VFQFN 裸露焊盤
供應商設備封裝: 20-QFN 裸露焊盤(4x4)
包裝: 帶卷 (TR)
2010 Microchip Technology Inc.
DS22265A-page 93
MCP444X/446X
FIGURE B-6:
Resistor Network Block
Diagram.
The characteristics of the wiper are determined by the
characteristics of the wiper switch at each of the
resistor networks tap points. Figure B-7 shows an
example of a wiper switch. As the device operational
voltage becomes lower, the characteristics of the wiper
switch change due to a lower voltage on the VG signal.
Figure B-7 shows an implementation of a wiper switch.
When the transistor is turned off, the switch resistance
is in the Giga
Ωs. When the transistor is turned on, the
switch resistance is dependent on the VG, VW and
VWCn voltages. This resistance is referred to as RW.
FIGURE B-7:
Wiper Switch.
So looking at the wiper voltage (VW) for the
3.0V and 1.8V data gives the graphs in Figure B-8 and
Figure B-9. In the 1.8V graph, as the VW approaches
0.8V, the voltage increases nonlinearly. Since V = I * R,
and the current (IW) is constant, it means that the
device resistance increased nonlinearly at around
wiper code 160.
FIGURE B-8:
Wiper Voltage (VW) vs.
Wiper Code (VDD = 3.0V, IW = 190 A).
FIGURE B-9:
Wiper Voltage (VW) vs.
Wiper Code (VDD = 1.8V, IW = 190 A).
RS
A
RS
B
RW (1)
W
RW (1)
Note 1:
The wiper resistance is dependent on
several factors including, wiper code,
device VDD, Terminal voltages (on A, B
and W), and temperature.
RAB
NMOS
PMOS
N0
Nn-1
N1
Nn
Nn-2
Nn-3
VW
VB
VA
VWC(n-2)
DVG
Note 1:
Wiper Resistance (RW) depends on the
voltages at the wiper switch nodes
(VG, VW and VWCn).
RW (1)
NMOS
PMOS
NWC
Wiper
VG (VDD/VSS)
“gate”
VW
VWCn
0.0
0.2
0.4
0.6
0.8
1.0
1.2
0
32
64
96
128 160 192 224 256
Wiper Code
Wiper
Voltage
(V)
-40C
+25C
+85C
+125C
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
0
32
64
96
128 160 192 224 256
Wiper Code
Wiper
Voltage
(V)
-40C
+25C
+85C
+125C
相關PDF資料
PDF描述
MCP4441T-502E/ML IC DGTL POT 129TAPS QUAD 20QFN
VI-BNP-MY-F3 CONVERTER MOD DC/DC 13.8V 50W
VI-BNP-MY-F1 CONVERTER MOD DC/DC 13.8V 50W
DS1747-70IND IC RTC RAM Y2K 5V 70NS 32-EDIP
VE-B1F-MV CONVERTER MOD DC/DC 72V 150W
相關代理商/技術參數
參數描述
MCP4442-103E/ST 功能描述:數字電位計 IC 10k I2C Quad Ch 7bit Nonvolatile Memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP4442-103E/ST 制造商:Microchip Technology Inc 功能描述:; End To End Resistance:10kohm; Track Ta 制造商:Microchip Technology Inc 功能描述:IC, DIG POT, 10kohm, 129STEPS, QUAD, TSSOP-14
MCP4442-104E/ST 功能描述:數字電位計 IC 100k I2C Quad Ch 7bt Nonvolatile Memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP4442-104E/ST 制造商:Microchip Technology Inc 功能描述:; End To End Resistance:100kohm; Track T 制造商:Microchip Technology Inc 功能描述:IC, DIG POT, 100kohm, 129STEPS, QUAD, TSSOP-14
MCP4442-503E/ST 功能描述:數字電位計 IC 50k I2C Quad Ch 7bit Nonvolatile Memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel