參數資料
型號： MCP6004-E/SL
廠商： Microchip Technology
文件頁數： 8/42頁
文件大?。?/td> 0K
描述： IC OPAMP QUAD 1.8V 1MHZ 14SOIC
標準包裝： 57
放大器類型： 通用
電路數： 4
輸出類型： 滿擺幅
轉換速率： 0.6 V/µs
增益帶寬積： 1MHz
電流 - 輸入偏壓： 1pA
電壓 - 輸入偏移： 4500µV
電流 - 電源： 100µA
電流 - 輸出 / 通道： 23mA
電壓 - 電源，單路/雙路(±)： 1.8 V ~ 6 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 14-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 14-SOIC
包裝： 管件
產品目錄頁面： 678 (CN2011-ZH PDF)
MCP6001/1R/1U/2/4
DS21733J-page 16
2009 Microchip Technology Inc.
4.7.3
PEAK DETECTOR
The MCP6001/2/4 op amp has a high input impedance,
rail-to-rail input/output and low input bias current, which
makes
this
device
suitable
for
peak
detector
applications. Figure 4-9 shows a peak detector circuit
with clear and sample switches. The peak-detection
cycle uses a clock (CLK), as shown in Figure 4-9.
At the rising edge of CLK, Sample Switch closes to
begin sampling. The peak voltage stored on C1 is
sampled to C2 for a sample time defined by tSAMP. At
the end of the sample time (falling edge of Sample
Signal), Clear Signal goes high and closes the Clear
Switch. When the Clear Switch closes, C1 discharges
through R1 for a time defined by tCLEAR. At the end of
the clear time (falling edge of Clear Signal), op amp A
begins to store the peak value of VIN on C1 for a time
defined by tDETECT.
In order to define tSAMP and tCLEAR, it is necessary to
determine the capacitor charging and discharging
period. The capacitor charging time is limited by the
amplifier source current, while the discharging time (
τ)
is defined using R1 (τ = R1C1). tDETECT is the time that
the input signal is sampled on C1 and is dependent on
the input voltage change frequency.
The op amp output current limit, and the size of the
storage capacitors (both C1 and C2), could create
slewing limitations as the input voltage (VIN) increases.
Current through a capacitor is dependent on the size of
the capacitor and the rate of voltage change. From this
relationship, the rate of voltage change or the slew rate
can be determined. For example, with an op amp short
circuit current of ISC = 25 mA and a load capacitor of
C1 = 0.1 F, then:
EQUATION 4-1:
This voltage rate of change is less than the MCP6001/2/4
slew rate of 0.6 V/s. When the input voltage swings
below the voltage across C1, D1 becomes reverse-
biased. This opens the feedback loop and rails the
amplifier. When the input voltage increases, the amplifier
recovers at its slew rate. Based on the rate of voltage
change shown in the above equation, it takes an
extended period of time to charge a 0.1 F capacitor. The
capacitors need to be selected so that the circuit is not
limited by the amplifier slew rate. Therefore, the
capacitors should be less than 40 F and a stabilizing
resistor (RISO) needs to be properly selected. (Refer to
FIGURE 4-9:
Peak Detector with Clear and Sample CMOS Analog Switches.
dV
C1
dt
-------------
I
SC
C
1
--------
=
25mA
0.1
μF
---------------
=
dV
C1
dt
-------------
250mV
μs
=
I
SC
C
1
dV
C1
dt
-------------
=
VIN
MCP6002
VC1
MCP6002
D1
Op Amp A
Op Amp B
VOUT
MCP6001
Op Amp C
C2
Sample Signal
Clear Signal
Clear
RISO
Sample
–
+
–
+
–
+
CLK
tSAMP
tCLEAR
tDETECT
Switch
1/2
R1
RISO VC2
C1
相關PDF資料
PDF描述
7-1676966-5 RES 120 OHM 2W 5% SMD
1-1879011-7 RES 1.00K OHM 2W 5% SMD
2-1879011-3 RES 1.80K OHM 2W 5% SMD
1879011-5 RES 330 OHM 2W 5% SMD
MCP6441T-E/LT IC OP AMP 450NA 9KHZ SNGL SC70-5
相關代理商/技術參數
參數描述
MCP6004ESN 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1 MHz Bandwidth Low Power Op Amp
MCP6004EST 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1 MHz Bandwidth Low Power Op Amp
MCP6004I 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1 MHz Bandwidth Low Power Op Amp
MCP6004-I/LT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1 MHz, Low-Power Op Amp
MCP6004-I/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1 MHz, Low-Power Op Amp
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*