參數資料
型號: MCP6021-E/ST
廠商: Microchip Technology
文件頁數: 10/42頁
文件大?。?/td> 0K
描述: IC OPAMP SNGL 2.5V 10MHZ 8TSSOP
標準包裝: 100
放大器類型: 通用
電路數: 1
輸出類型: 滿擺幅
轉換速率: 7 V/µs
增益帶寬積: 10MHz
電流 - 輸入偏壓: 1pA
電壓 - 輸入偏移: 500µV
電流 - 電源: 1mA
電流 - 輸出 / 通道: 30mA
電壓 - 電源,單路/雙路(±): 2.5 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 8-TSSOP
包裝: 管件
產品目錄頁面: 678 (CN2011-ZH PDF)
MCP6021/1R/2/3/4
DS21685D-page 18
2009 Microchip Technology Inc.
When driving large capacitive loads with these op
amps (e.g., > 60 pF when G = +1), a small series
resistor at the output (RISO in Figure 4-3) improves the
feedback loop’s phase margin (stability) by making the
load resistive at higher frequencies. The bandwidth will
be generally lower than the bandwidth with no
capacitive load.
FIGURE 4-3:
Output Resistor RISO
Stabilizes Large Capacitive Loads.
Figure 4-4 gives recommended RISO values for
different capacitive loads and gains. The x-axis is the
normalized load capacitance (CL/GN), where GN is the
circuit’s noise gain. For non-inverting gains, GN and the
Signal Gain are equal. For inverting gains, GN is
1+|Signal Gain| (e.g., -1 V/V gives GN = +2 V/V).
FIGURE 4-4:
Recommended RISO values
for capacitive loads.
After selecting RISO for your circuit, double-check the
resulting
frequency
response
peaking
and
step
response overshoot. Modify RISO’s value until the
response is reasonable. Evaluation on the bench and
simulations with the MCP6021/1R/2/3/4 Spice macro
model are helpful.
4.4
Gain Peaking
Figure 2-35 and Figure 2-36 use RF =1kΩ to avoid
(frequency
response)
gain
peaking
and
(step
response) overshoot. The capacitance to ground at the
inverting input (CG) is the op amp’s common mode
input capacitance plus board parasitic capacitance. CG
is in parallel with RG, which causes an increase in gain
at high frequencies for non-inverting gains greater than
1 V/V (unity gain). CG also reduces the phase margin
of the feedback loop for both non-inverting and
inverting gains.
FIGURE 4-5:
Non-inverting Gain Circuit
with Parasitic Capacitance.
The largest value of RF in Figure 4-5 that should be
used is a function of noise gain (see GN in Section 4.3
for various conditions. Other compensation techniques
may be used, but they tend to be more complicated to
the design.
FIGURE 4-6:
Non-inverting gain circuit
with parasitic capacitance.
4.5
MCP6023 Chip Select (CS)
The MCP6023 is a single amplifier with chip select
(CS). When CS is pulled high, the supply current drops
to 10 nA (typical) and flows through the CS pin to VSS.
When this happens, the amplifier output is put into a
high-impedance state. By pulling CS low, the amplifier
is enabled. The CS pin has an internal 5 M
Ω (typical)
pulldown resistor connected to VSS, so it will go low if
the CS pin is left floating. Figure 1-1 and Figure 2-39
show the output voltage and supply current response to
a CS pulse.
VIN
MCP602X
RISO
VOUT
CL
10
100
1,000
10
100
1,000
10,000
Normalized Capacitance; CL/GN (pF)
Recommended
R
IS
O
(
Ω
)
GN ≥ +1
VIN
RG
RF
VOUT
CG
1.E+02
1.E+03
1.E+04
1.E+05
110
Noise Gain; GN (V/V)
Maximum
R
F
(
Ω
)
GN > +1 V/V
100
1k
10k
100k
CG = 7 pF
CG = 20 pF
CG = 50 pF
CG = 100 pF
相關PDF資料
PDF描述
TSW-132-08-L-D CONN HEADER 64POS .100" DL GOLD
CLT-103-02-L-D CONN RCPT 6POS DUAL 2MM SMD
TSW-118-07-S-D CONN HEADER 36POS .100" DL GOLD
34067 CONN SPLICE BUTT 16-22 AWG .120
CLT-104-02-L-D CONN RCPT 8POS DUAL 2MM SMD
相關代理商/技術參數
參數描述
MCP6021-I/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Rail-to-Rail Input/Output, 10 MHz Op Amps
MCP6021-I/OT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Rail-to-Rail Input/Output, 10 MHz Op Amps
MCP6021-I/P 功能描述:運算放大器 - 運放 Single 2.5V 10MHz RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MCP6021-I/SL 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Rail-to-Rail Input/Output, 10 MHz Op Amps
MCP6021-I/SN 功能描述:運算放大器 - 運放 Single 2.5V 10MHz RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel