參數資料
型號： MCP6033-E/MC
廠商： Microchip Technology
文件頁數： 9/34頁
文件大小： 0K
描述： IC OPAMP SNGL 1.8V W/CS 8DFN
標準包裝： 150
放大器類型： 通用
電路數： 1
輸出類型： 滿擺幅
轉換速率： 0.004 V/µs
增益帶寬積： 10kHz
電流 - 輸入偏壓： 1pA
電壓 - 輸入偏移： 150µV
電流 - 電源： 0.9µA
電流 - 輸出 / 通道： 23mA
電壓 - 電源，單路/雙路(±)： 1.8 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-VFDFN 裸露焊盤
供應商設備封裝： 8-DFN（2x3）
包裝： 管件
2008 Microchip Technology Inc.
DS22041B-page 17
MCP6031/2/3/4
4.9
Application Circuits
4.9.1
BATTERY CURRENT SENSING
The MCP6031/2/3/4 op amps’ Common Mode Input
Range, which goes 0.3V beyond both supply rails,
supports their use in high side and low side battery
current sensing applications. The ultra low quiescent
current (0.9 A, typical) helps prolong battery life, and
the rail-to-rail output supports detection of low currents.
Figure 4-7 shows a high side battery current sensor
circuit. The 10
Ω resistor is sized to minimize power
losses. The battery current (IDD) through the 10Ω
resistor causes its top terminal to be more negative
than the bottom terminal. This keeps the common
mode input voltage of the op amp below VDD, which is
within its allowed range. The output of the op amp will
also be below VDD, which is within its Maximum Output
Voltage Swing specification.
FIGURE 4-7:
High Side Battery Current
Sensor.
4.9.2
PRECISION COMPARATOR
Use high gain before a comparator to improve the lat-
ter’s input offset performance. Figure 4-8 shows a gain
of 11 V/V placed before a comparator. The reference
voltage VREF can be any value between the supply
rails.
FIGURE 4-8:
Precision, Non-inverting
Comparator.
4.9.3
DRIVING MCP3421
ΔΣ A/D
CONVERTER
A RSH and CSH snubber reduces the output impedance
of MCP6031 op amp, which reduces the gain error
caused by switching transients, which occur at the
MCP3421 ADC's sampling rate. The snubber also
maintains feedback stability and avoids AC response
peaking and step response overshoot and ringing
(caused by the op amp’s inductive output impedance
resonating with the ADC’s input capacitance). The cost
for this improvement is low. Best of all, using an op amp
with higher supply current is avoided. See Figure 4-9.
This figure also includes a resistor to balance the
impedance at the ADC's inputs (RBAL) at the sampling
frequency; it may not be needed in all designs.
FIGURE 4-9:
Driving the MCP3421 using
an R-C Snubber.
VDD
IDD
MCP6031
100 k
Ω
1M
Ω
1.4V
VOUT
10
Ω
to
5.5V
I
DD
V
DD
V
OUT
–
10 V/V
() 10
Ω
()
------------------------------------------
=
VIN
1M
Ω
VOUT
MCP6031
100 k
Ω
MCP6541
VREF
VIN
MCP6031
RSH
CSH
1.00 k
Ω
2.2 F
RBAL
1.00 k
Ω
MCP3421
ΔΣ
1.00 k
Ω
ZIND
2.25 M
Ω
相關PDF資料
PDF描述
LT1127ACN#PBF IC OP-AMP DECOMPENSAT QUAD 14DIP
2036-60-C2 GAS DISCHARGE TUBE MINI 3 POLE
1-170823-0 CONN INSULATION SLEEVE .110
2030.0545 FUSE 400MA 125V TELCM 18.8MM PCB
3-336369-5 CONN HOUSING 1CIRCUIT NYLON 6/6
相關代理商/技術參數
參數描述
MCP6033T 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:0.9 uA, High Precision Op Amps
MCP6033T-E/MC 功能描述:運算放大器 - 運放 SNGL 18V 10kHz Op Amp w/ CS E temp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MCP6033TE/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:0.9 uA, High Precision Op Amps
MCP6033T-E/MS 功能描述:運算放大器 - 運放 S-1.8V 14kHz Op Amp w/ CS E temp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MCP6033T-E/OT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:0.9 μA, High Precision Op Amps
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*