- 您現在的位置：買賣IC網 > PDF目錄6193 > MCP6N11T-001E/MNY (Microchip Technology)IC AMP INSTR RRIO 500KHZ 8TDFN PDF資料下載
參數資料
| 型號： | MCP6N11T-001E/MNY |
| 廠商： | Microchip Technology |
| 文件頁數： | 18/50頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP INSTR RRIO 500KHZ 8TDFN |
| 標準包裝： | 1 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 9 V/µs |
| 增益帶寬積： | 500kHz |
| 電流 - 輸入偏壓： | 10pA |
| 電壓 - 輸入偏移： | 3000µV |
| 電流 - 電源： | 800µA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-TDFN（2x3） |
| 包裝： | 標準包裝 |
| 其它名稱： | MCP6N11T-001E/MNYDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
2011 Microchip Technology Inc.
DS25073A-page 25
MCP6N11
3.0
PIN DESCRIPTIONS
Descriptions of the pins are listed in Table 3-1.
3.1
Analog Signal Inputs
The non-inverting and inverting inputs (VIP, and VIM)
are high-impedance CMOS inputs with low bias
currents.
3.2
Analog Feedback Input
The analog feedback input (VFG) is the inverting input
of the second input stage. The external feedback
components (RF and RG) are connected to this pin. It is
a high-impedance CMOS input with low bias current.
3.3
Analog Reference Input
The analog reference input (VREF) is the non-inverting
input of the second input stage; it shifts VOUT to its
desired range. The external gain resistor (RG) is
connected to this pin. It is a high-impedance CMOS
input with low bias current.
3.4
Analog Output
The analog output (VOUT) is a low-impedance voltage
output. It represents the differential input voltage
(VDM =VIP –VIM), with gain GDM and is shifted by
VREF. The external feedback resistor (RF) is connected
to this pin.
3.5
Power Supply Pins
The positive power supply (VDD) is 1.8V to 5.5V higher
than the negative power supply (VSS). For normal
operation, the other pins are between VSS and VDD.
Typically, these parts are used in a single (positive)
supply configuration. In this case, VSS is connected to
ground and VDD is connected to the supply; VDD will
need bypass capacitors.
3.6
Digital Enable and VOS Calibration
Input
This input (EN/CAL) is a CMOS, Schmitt-triggered
input that controls the active, low power and VOS
calibration modes of operation. When this pin goes low,
the part is placed into a low power mode and the output
is high-Z. When this pin goes high, the amplifier’s input
offset voltage is corrected by the calibration circuitry,
then the output is re-connected to the VOUT pin, which
becomes low impedance, and the part resumes normal
operation.
3.7
Exposed Thermal Pad (EP)
There is an internal connection between the Exposed
Thermal Pad (EP) and the VSS pin; they must be
connected to the same potential on the Printed Circuit
Board (PCB).
This pad can be connected to a PCB ground plane to
provide a larger heat sink. This improves the package
thermal resistance (
θJA).
TABLE 3-1:
PIN FUNCTION TABLE
MCP6N11
Symbol
Description
SOIC
TDFN
11
VFG
Feedback Input
22
VIM
Inverting Input
33
VIP
Non-inverting Input
44
VSS
Negative Power Supply
55
VREF
Reference Input
66
VOUT
Output
77
VDD
Positive Power Supply
88
EN/CAL
Enable/VOS Calibrate Digital Input
—
9
EP
Exposed Thermal Pad (EP); must be connected to VSS
相關PDF資料 |
PDF描述 |
|---|---|
| 953105-2000-AR-TP | CONN SOCKET 5POS 2MM VERT SMD |
| 963206-2000-AR-TP | CONN SOCKET DUAL 6POS GOLD SMD |
| 963106-2000-AR-TP | CONN SOCKET SGL 6POS GOLD SMD |
| PPTC251LGBN-RC | CONN FEMALE 25POS .100" R/A TIN |
| 66950-006 | VERT CARD CONN SR .100" 15AU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP6N11T-002E/MNY | 功能描述:儀表放大器 Sngl Instrumentation Amp mCal E temp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| MCP6N11T-002E/SN | 功能描述:儀表放大器 Sngl Instrumentation Amp mCal E temp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| MCP6N11T-005E/MNY | 功能描述:儀表放大器 Sngl Instrumentation Amp mCal E temp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| MCP6N11T-005E/SN | 功能描述:儀表放大器 Sngl Instrumentation Amp mCal E temp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| MCP6N11T-010E/MNY | 功能描述:儀表放大器 Sngl Instrumentation Amp mCal E temp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。