參數資料
型號： MCP73841
廠商： Microchip Technology Inc.
英文描述： Advanced Single or Dual Cell Lithium-Ion/ Lithium-Polymer Charge Management Controllers
中文描述： 先進的單節或雙節鋰離子/鋰聚合物充電管理控制器
文件頁數： 11/24頁
文件大?。?/td> 414K
代理商： MCP73841
2004 Microchip Technology Inc.
DS21823B-page 11
MCP73841/2/3/4
4.0
DEVICE OVERVIEW
The MCP7384X family of devices are highly advanced,
linear charge management controllers. Figure 4-1
depicts the operational flow algorithm from charge
initiation to completion and automatic recharge.
4.1
Charge Qualification and
Preconditioning
Upon insertion of a battery or application of an external
supply, the MCP7384X family of devices automatically
perform a series of safety checks to qualify the charge.
The input source voltage must be above the
undervoltage lockout threshold, the enable pin must be
above the logic-high level and the cell temperature
monitor must be within the upper and lower thresholds.
The cell temperature monitor applies to both the
MCP73841 and MCP73842, with the qualification
parameters being continuously monitored. Deviation
beyond the limits automatically suspends or terminates
the charge cycle.
Once the qualification parameters have been met, the
MCP7384X initiates a charge cycle. The charge status
output is pulled low throughout the charge cycle (see
Table 5-1 for charge status outputs). If the battery
voltage is below the preconditioning threshold (V
PTH
),
the MCP7384X preconditions the battery with a trickle-
charge. The preconditioning current is set to
approximately 10% of the fast charge regulation
current. The preconditioning trickle-charge safely
replenishes deeply depleted cells and minimizes heat
dissipation in the external pass transistor during the
initial charge cycle. If the battery voltage has not
exceeded the preconditioning threshold before the
preconditioning timer has expired, a fault is indicated
and the charge cycle is terminated.
4.2
Constant-Current Regulation –
Fast Charge
Preconditioning ends and fast charging begins, when
the battery voltage exceeds the preconditioning
threshold. Fast charge regulates to a constant-current,
I
REG
, based on the supply voltage minus the voltage at
the SENSE input (V
FCS
) developed by the drop across
an external sense resistor (R
SENSE
). Fast charge
continues until the battery voltage reaches the
regulation voltage (V
REG
); or until the fast charge timer
expires. In this case, a fault is indicated and the charge
cycle is terminated.
4.3
Constant-Voltage Regulation
When the battery voltage reaches the regulation
voltage (V
REG
), constant-voltage regulation begins.
The MCP7384X monitors the battery voltage at the
V
BAT
pin. This input is tied directly to the positive
terminal of the battery. The MCP7384X is offered in
four fixed-voltage versions for single or dual series cell
battery packs with either coke or graphite anodes:
- 4.1V (MCP73841-4.1, MCP73843-4.1)
- 4.2V (MCP73841-4.2, MCP73843-4.2)
- 8.2V (MCP73842-8.2, MCP73844-8.2)
- 8.4V (MCP73842-8.4, MCP73844-8.4)
4.4
Charge Cycle Completion and
Automatic Re-Charge
The MCP7384X monitors the charging current during
the constant-voltage regulation phase. The charge
cycle is considered complete when the charge current
has diminished below approximately 7% of the
regulation current (I
REG
) or the elapsed timer has
expired.
The MCP7384X automatically begins a new charge
cycle when the battery voltage falls below the recharge
threshold (V
RTH
), assuming all the qualification
parameters are met.
相關PDF資料
PDF描述
MCP73844 Advanced Single or Dual Cell Lithium-Ion/ Lithium-Polymer Charge Management Controllers
MCP73843 Advanced Single or Dual Cell Lithium-Ion/ Lithium-Polymer Charge Management Controllers
MCP73861 Advanced Single Cell, Fully Integrated Li-Ion /Li-Polymer Charge Management Controllers(增強型單節高度集成的鋰離子/鋰聚合物充電管理控制器)
MCP73862 Advanced Dual Cell, Fully Integrated Li-Ion /Li-Polymer Charge Management Controllers(增強型兩節高度集成的鋰離子/鋰聚合物充電管理控制器)
MCP810 Microcontroller Supervisory Circuit with Push-Pull Output(帶推挽輸出的微控制器監控電路)
相關代理商/技術參數
參數描述
MCP73841_13 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Advanced Single or Dual Cell Lithium-Ion/ Lithium-Polymer Charge Management Controllers
MCP73841-410I/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Advanced Single or Dual Cell Lithium-Ion/ Lithium-Polymer Charge Management Controllers
MCP73841-410I/UN 功能描述:電池管理 w/ Ch Sfty & Temp Mn RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
MCP73841-420I/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Advanced Single or Dual Cell Lithium-Ion/ Lithium-Polymer Charge Management Controllers
MCP73841-420I/UN 功能描述:電池管理 w/ Ch Sfty & Temp Mn RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*