- 您現在的位置：買賣IC網 > PDF目錄67987 > MCP7940N-I/MS REAL TIME CLOCK, PDSO8 PDF資料下載
參數資料
| 型號： | MCP7940N-I/MS |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | REAL TIME CLOCK, PDSO8 |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 35/36頁 |
| 文件大?。?/td> | 551K |
| 代理商： | MCP7940N-I/MS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁
MCP7940N
DS25010A-page 8
2011 Microchip Technology Inc.
FIGURE 3-2:
ACKNOWLEDGE TIMING
3.1.2
DEVICE ADDRESSING AND OPERATION
A control byte is the first byte received following the
Start condition from the master device (Figure 3-2).
The control byte for accessing the SRAM and RTCC
registers are set to ‘1101111’. The RTCC registers and
the SRAM share the same address space.
The last bit of the control byte defines the operation to
be performed. When set to a ‘1’ a read operation is
selected, and when set to a ‘0’ a write operation is
selected. The next byte received defines the address of
the data byte (Figure 3-3). The upper address bits are
transferred first, followed by the Least Significant bits
(LSb).
Following the Start condition, the MCP7940N monitors
the SDA bus, checking the device type identifier being
transmitted. Upon receiving an ‘1101111’ code, the
slave device outputs an Acknowledge signal on the
SDA line. Depending on the state of the R/W bit, the
MCP7940N will select a read or write operation.
FIGURE 3-3:
ADDRESS SEQUENCE BIT ASSIGNMENTS
SCL
9
8
7
6
5
4
3
2
11
2
3
Transmitter must release the SDA line at this point
allowing the Receiver to pull the SDA line low to
acknowledge the previous eight bits of data.
Receiver must release the SDA line at this point
so the Transmitter can continue sending data.
Data from transmitter
SDA
Acknowledge
Bit
1
101
R/W
X
A
0
SRAM RTCC CONTROL BYTE
ADDRESS BYTE
CONTROL
CODE
111
X = Don’t Care
相關PDF資料 |
PDF描述 |
|---|---|
| MCP7940NT-I/ST | REAL TIME CLOCK, PDSO8 |
| MCP7940NT-I/SN | REAL TIME CLOCK, PDSO8 |
| MCP7940NT-I/MS | REAL TIME CLOCK, PDSO8 |
| MCP79411-I/SN | REAL TIME CLOCK, PDSO8 |
| MCP79411-I/MNY | REAL TIME CLOCK, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP7940NT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low-Cost I2C? Real-Time Clock/Calendar with SRAM and Battery Switchover |
| MCP7940NT-E/MNY | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low-Cost I2C Real-Time Clock/Calendar with SRAM and Battery Switchover |
| MCP7940NT-E/MS | 制造商:Microchip Technology Inc 功能描述:I2C GP RTCC, 64B SRAM, EXT - Tape and Reel 制造商:Microchip Technology Inc 功能描述:IC RTCC 64B SRAM GP I2C 8MSOP |
| MCP7940NT-E/SN | 功能描述:實時時鐘 I2C GP RTCC 64B SRAM EXT RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| MCP7940NT-E/ST | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low-Cost I2C Real-Time Clock/Calendar with SRAM and Battery Switchover |
發布緊急采購，3分鐘左右您將得到回復。