參數資料
型號: MCRF250
廠商: Microchip Technology Inc.
英文描述: 125 kHz microID Passive RFID Device with Anti-Collision
中文描述: 125千赫microID無源RFID設備與反碰撞
文件頁數: 5/24頁
文件大?。?/td> 395K
代理商: MCRF250
2003 Microchip Technology Inc.
DS21267F-page 5
MCRF250
2.2
Configuration Register and
Control Logic
The configuration register determines the operational
parameters of the device. The configuration register
can not be programmed contactlessly; it is
programmed during wafer probe at the Microchip fac-
tory. CB11 is always a one; CB12 is set when success-
ful contact or contactless programming of the data
array has been completed. Once CB12 is set, device
programming and erasing is disabled. Table 2-1
contains a description of the bit functions of the control
register.
2.2.1
BAUD RATE TIMING OPTION
The chip will access data at a baud rate determined by
bits CB2, CB3, and CB4 of the configuration register.
For example, MOD32 (CB2 =
0
, CB3 =
1
, CB4 =
1
) has
32 RF cycles per bit. This gives the data rate of 4 kHz
for the RF carrier frequency of 128 kHz.
The default timing is MOD 128 (F
CLK
/128), and this
mode is used for contact and contactless program-
ming. Once the array is successfully programmed, the
lock bit CB12 is set. When the lock bit is set, program-
ming and erasing the device becomes permanently
disabled. The configuration register has no effect on
device timing until the EEPROM data array is
programmed (CB12 =
1
).
2.2.2
DATA ENCODING OPTION
This logic acts upon the serial data being read from the
EEPROM. The logic encodes the data according to the
configuration bits CB6 and CB7. CB6 and CB7
determine the data encoding method. The available
choices are:
Non-return to zero-level (NRZ_L)
Biphase_S (Differential)
Biphase_L (Manchester)
Inverted Manchester
2.2.3
MODULATION OPTION
CB8 and CB9 determine the modulation protocol of the
encoded data. The available choices are:
ASK
FSK
PSK_1
PSK_2
When ASK (direct) option is chosen, the encoded data
is fed into the modulation transistor without change.
When FSK option is chosen, the encoded data is
represented by:
a)
Sets of 10 RF carrier cycles (first 5 cycles
higher amplitude, the last 5 cycles
lower
amplitude) for logic “high” level.
b)
Sets of 8 RF carrier cycles (first 4 cycles
higher amplitude, the last 4 cycles
lower
amplitude) for logic “l(fā)ow” level.
For example, FSK signal for MOD40 is represented:
a)
4 sets of 10 RF carrier cycles for data ‘
1
’.
b)
5 sets of 8 RF carrier cycles for data ‘
0
’.
Refer to Figure 2-2 for the FSK signal with MOD40
option.
The PSK_1 represents change in the phase of the
For example, the phase changes when the encoded
data is changed from ‘
1
’ to ‘
0
’, or from ‘
0
’ to ‘
1
’.
The PSK_2 represents change in the phase at the
change on ‘
1
’. For example, the phase changes when
the encoded data is changed from ‘
0
’ to ‘
1
’, or from ‘
1
to ‘
1
’.
FIGURE 2-2:
ENCODED DATA AND FSK OUTPUT SIGNAL FOR MOD40 OPTION
Encoded Data ‘
1
Encoded Data ‘
0
40 RF cycles
40 RF cycles
5 cycles (HI)
5 cycles (LO)
4 cycles (HI)
4 cycles (LO)
相關PDF資料
PDF描述
MD82C55B CMOS Programmable Peripheral Interface
MD900 Ultra High Sensitivity Gateable Channel Photomultiplier DC-Modules
MDFB51 Fast Recovery Diode
MDFB5120 Fast Recovery Diode
MDFB5122 Fast Recovery Diode
相關代理商/技術參數
參數描述
MCRF250-I/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:125 kHz microID Passive RFID Device with Anti-Collision
MCRF250-I/S 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:125 kHz microID Passive RFID Device with Anti-Collision
MCRF250-I/SN 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:125 kHz microID Passive RFID Device with Anti-Collision
MCRF250-I/W 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:125 kHz microID Passive RFID Device with Anti-Collision
MCRF250-I/W40A 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:125 kHz microID Passive RFID Device with Anti-Collision