- 您現在的位置：買賣IC網 > PDF目錄1953 > MCZ145010EG (Freescale Semiconductor)IC SMOKE DETECT PHOTOELEC 16SOIC PDF資料下載
參數資料
| 型號： | MCZ145010EG |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 8/12頁 |
| 文件大小： | 0K |
| 描述： | IC SMOKE DETECT PHOTOELEC 16SOIC |
| 標準包裝： | 47 |
| 類型： | 煙霧探測器 |
| 輸入類型： | 光電 |
| 輸出類型： | 電壓 |
| 電流 - 電源： | 12µA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 管件 |
Sensors
Freescale Semiconductor
5
MC145010
Table 4. Pin Description
Pin
Symbol
Description
1
C1
A capacitor connected to this pin, shown in Figure 8, determines the gain of the on-chip photo amplifier during push button
test and chamber sensitivity test (high gain). The capacitor value is chosen such that the alarm is tripped from background
reflections in the chamber during push button test.
Av 1 + (C1/10) where C1 is in pF. CAUTION: The value of the closed-loop gain should not exceed 10,000.
2
C2
A capacitor connected to this pin as shown in Figure 8 determines the gain of the on-chip photo amplifier except during
push button or chamber sensitivity tests. Av ≈ 1 + (C2/10) where C2 is in pF. This gain increases about 10% during the
IRED pulse, after two consecutive local smoke detections.
Resistor R14 must be installed in series with C2. R14
≈ [1/(12√C2)] - 680 where R14 is in ohms and C2 is in farads.
3
DETECT This input to the high-gain pulse amplifier is tied to the cathode of an external photodiodes. The photodiodes should have
low capacitance and low dark leakage current. The diode must be shunted by a load resistor and is operated at zero bias.
The Detect input must be ac/dc decoupled from all other signals, VDD, and VSS. Lead length and/or foil traces to this pin
must be minimized, also. See Figure 9.
4
STROBE This output provides a strobed, regulated voltage referenced to VDD. The temperature coefficient of this voltage is ± 0.2%/
°C maximum from - 10° to 60°C. The supply-voltage coefficient (line regulation) is ± 0.2%/V maximum from 6 to 12 V.
Strobe is tied to external resistor string R8, R9, and R10.
5
VDD
This pin is connected to the positive supply potential and may range from +6 to +12 V with respect to VSS. CAUTION: In
battery-powered applications, reverse-polarity protection must be provided externally.
6
IRED
This output provides pulsed base current for external NPN transistor Q1 used as the infrared emitter driver. Q1 must have
β ≥ 100. At 10 mA, the temperature coefficient of the output voltage is typically + 0.5%/°C from - 10° to 60°C. The supply-
voltage coefficient (line regulation) is
± 0.2%/V maximum from 6 to 12 V. The IRED pulse width (active-high) is determined
by external components R1 and C3. With a 100 k
/1500 pF combination, the nominal width is 105 s. To minimize noise
impact, IRED is not active when the visible LED and horn outputs are active. IRED is active near the end of Strobe pulses
for Smoke Tests, Chamber Sensitivity Test, and Push button Test.
7
I/O
This pin can be used to connect up to 40 units together in a wired-OR configuration for common signaling. VSS is used as
the return. An on-chip current sink minimizes noise pick up during non-smoke conditions and eliminates the need for an
external pull-down resistor to complete the wired-OR. Remote units at lower supply voltages do not draw excessive current
from a sending unit at a higher supply voltage.
I/O can also be used to activate escape lights, auxiliary alarms, remote alarms, and/or auto-dialers.
As an input, this pin feeds a positive-edge-triggered flip-flop whose output is sampled nominally every 625 ms during
standby (using the recommended component values). A local-smoke condition or the push button-test mode forces this
current-limited output to source current. All input signals are ignored when I/O is sourcing current. I/O is disabled by the
on-chip power-on reset to eliminate nuisance signaling during battery changes or system power-up. If unused, I/O must
be left unconnected.
8
BRASS
This half of the push-pull driver output is connected to the metal support electrode of a piezoelectric audio transducer and
to the horn-starting resistor. A continuous modulated tone from the transducer is a smoke alarm indicating either local or
remote smoke. A short beep or chirp is a trouble alarm indicating a low supply or degraded chamber sensitivity.
9
SILVER
This half of the push-pull driver output is connected to the ceramic electrode of a piezoelectric transducer and to the horn-
starting capacitor.
10
FEEDBA
CK
This input is connected to both the feedback electrode of a self-resonating piezoelectric transducer and the horn-starting
resistor and capacitor through current-limiting resistor R4. If unused, this pin must be tied to VSS or VDD.
11
LED
This active-low open-drain output directly drives an external visible LED at the pulse rates indicated below. The pulse width
is equal to the OSC period.
The load for the low-supply test is applied by this output. This low-supply test is non-coincident with the smoke tests,
chamber sensitivity test, push button test, or any alarm signals.
The LED also provides a visual indication of the detector status as follows, assuming the component values shown in
Figure 8: Standby (includes low-supply and chamber sensitivity tests) - Pulses every 43 seconds (nominal) Local Smoke
- Pulses every 0.67 seconds (nominal) Remote Smoke - No pulses
Push button Test - Pulses every 0.67 seconds (nominal)
12
OSC
This pin is used in conjunction with external resistor R2 (10 M
) to VDD and external capacitor C3 (1500 pF) to VDD to
form an oscillator with a nominal period of 10.5 ms.
13
R1
This pin is used in conjunction with resistor R1 (100 k
) to pin 12 and C3 (1500 pF, see pin 12 description) to determine
the IRED pulse width. With this RC combination, the nominal pulse width is 105
s.
14
VSS
This pin is the negative supply potential and the return for the I/O pin. Pin 14 is usually tied to ground.
15
LOW-
SUPPLY
TRIP
This pin is connected to an external voltage which determines the low-supply alarm threshold. The trip voltage is obtained
through a resistor divider connected between the VDD and LED pins. The low-supply alarm threshold voltage (in volts) ≈
(5R7/R6) + 5 where R6 and R7 are in the same units.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ145012EG | IC SMOKE DETECT PHOTOELEC 16SOIC |
| MCZ33094EG | IC IGNITION CONTROL 12V 16-SOIC |
| MCZ33287EG | IC DRIVER DUAL LOSIDE MON 20SOIC |
| MCZ33290EF | IC SER LNK INTER ISO KLINE 8SOIC |
| MCZ33298EG | IC SWITCH 8X LOSIDE W/SPI 24SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ145010EGR2 | 功能描述:煙霧報警器 SMOKE DET.PHOTO RoHS:否 制造商:ELMOS Semiconductor 描述/功能:Smoke detector controller 感應方式:Photoelectric 工作電源電壓:24 V 輸出信號類型: |
| MCZ145011DW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Photoelectric Smoke Detector IC with I/O For Line-Powered Applications |
| MCZ145012EG | 功能描述:煙霧報警器 PHOTO SMKE DET/NFPA TONE RoHS:否 制造商:ELMOS Semiconductor 描述/功能:Smoke detector controller 感應方式:Photoelectric 工作電源電壓:24 V 輸出信號類型: |
| MCZ145012EG/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Photoelectric Smoke Detector IC with I/O and Temporal Pattern Horn Driver |
| MCZ145012EGR2 | 功能描述:煙霧報警器 PHOTO SMKE DET/NFPA RoHS:否 制造商:ELMOS Semiconductor 描述/功能:Smoke detector controller 感應方式:Photoelectric 工作電源電壓:24 V 輸出信號類型: |
發布緊急采購，3分鐘左右您將得到回復。