- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ146012EG (飛思卡爾半導體(中國)有限公司) Low Power CMOS Photoelectric Smoke Detector IC PDF資料下載
參數資料
| 型號： | MCZ146012EG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Low Power CMOS Photoelectric Smoke Detector IC |
| 中文描述： | 低功耗CMOS集成電路光電感煙探測器 |
| 文件頁數： | 10/18頁 |
| 文件大小： | 358K |
| 代理商： | MCZ146012EG |
Sensors
10
Freescale Semiconductor
MC146012
The load for the low-supply test is non-coincident with the
smoke tests, chamber sensitivity test, pushbutton test, or any
alarm signals.
The LED also provides a visual indication of the detector
status as follows, assuming the component values shown in
Figure 4
:
Standby (includes low-supply and chamber sensitivity
tests) — Pulses every 32.4 seconds.
Local Smoke — Pulses every 2.0 seconds (typical)
Mute — Pulses every 2.0 seconds (typical)
Remote Smoke — No Pulses
Pushbutton test — Pulses every 2.0 seconds
OSC (PIN 12)
This pin is used in conjunction with external resistor R2
(7.5 M
) to V
DD
and external capacitor C3 (1500 pF) to V
DD
to form an oscillator with a nominal period of 7.9 msec
(typical).
R1 (PIN 13)
This pin is use din conjunction with resistor R1(100 k
) to
pin 12 and C3 (1500 pF, see pin 12 description) to determine
the IRED pulse width. With this RC combination, the nominal
pulse width is 105
μ
s.
V
SS
(PIN 14)
This pin is the negative supply potential and the return for
the I/O pin. Pin 14 is usually tied to Ground.
LOW-SUPPLY TRIP (PIN 15)
This pin is connected to an external voltage which
determines the low-supply alarm threshold. The trip voltage
is obtained through a resistor divider connected between the
V
DD
and LED pins. The low-supply alarm threshold voltage
(in volts) = (5R7/R6)+5 where R6 and R7 are in the same
units.
TEST/MUTE (PIN 16)
This input has an on-chip pull-down device and is used to
manually invoke a test mode, a mute mode, or a calibration
mode.
The
Pushbutton Test
mode is initiated by a high level at
Pin 16 (usually a depression of a S.P.S.T. normally-open
pushbutton switch to V
DD
). After one oscillator cycle, the
IRED pulses approximately every 1.0 second, regardless of
the presence of smoke. Additionally, the amplifier gain is
increased by automatic selection of C1. Therefore the
background reflections in the smoke chamber may be
interpreted as smoke, generating a simulated smoke
condition. After the second IRED pulse, a successful test
activates the horn-driver and I/O circuits. The active I/O
allows remote signaling for a system testing. When the
Pushbutton Test switch is released, the Test input returns to
V
SS
due to the on-chip pull-down device. After one oscillator
cycle, the amplifier gain returns to normal, thereby removing
the simulated smoke condition. After two additional IRED
pulses, less than three seconds, the IC exits the alarm mode
and returns to standby timing.
The
Pushbutton Test will
also activate the
Alarm Memory
feature. If there was a previous alarm detected by the unit,
the horn will chirp every second as long as the Test Button
is pressed. Upon releasing of the Test Button, Alarm memory
will be reset. Subsequent pressing of the Test Button will
result in a
Pushbutton Test f
or simulated smoke.
Pressing the Test Button while in the MUTE mode will
result in resetting of MUTE (and additionally a normal
Pushbutton Test).
The MUTE mode (IMF) is initiated by a mid level voltage
(around V
DD
) at pin 16. A parallel Mute Button to an
existing Test Button needs to be installed at the test pin. A
smoke condition must be present for the MUTE mode to be
activated. If a no smoke condition gets detected while in the
MUTE mode, the IMF 8 minute window gets reset. The unit
will return to Standby mode.
Once in the MUTE mode, the audible smoke alarm (horn)
is temporarily disabled for approximately 8 minutes while
smoke condition is being detected. A visual smoke alarm will
remain (LED flashing) during MUTE mode. A high smoke
voltage reference will also be activated at this time.
Simultaneous smoke and high smoke sampling will allow the
unit to enable the horn driver in case a high smoke condition
occurs during MUTE where the high smoke threshold is
crossed.
The MUTE mode can be overridden by the following
conditions: 1) a no smoke condition is detected, 2) high
smoke level detected, 3) remote smoke detected through I/O,
4) reset through test Button, 5) timeout of 8 minute window.
To help prevent a jammed Mute Button condition, the divider
string on the Mute Button should include a resistor to V
DD
,
R15 (around 10 M
) and a resistor R16 (4.7 M
) and
capacitor, C7 (0.047 mF) in series to V
SS
.
CALIBRATION
To facilitate checking the sensitivity and calibrating smoke
detectors, the MC146012 can be placed in Calibration mode.
In this mode, certain device pins are controlled/reconfigured
as shown in
Table 4
. To place the part in Calibration mode,
Pin 16 (Test/ Mute) must be pulled below V
SS
pin with 100
μ
A
continuously drawn out of the pin for at least one cycle of the
OSC pin. To exit this mode, the Test/ Mute pin is floated for at
least one OSC cycle.
In the Calibration mode, the IRED pulse rate is increased.
An IRED pulse occurs every clock cycle. Also, Strobe is
always Active Low. It is recommended to short R12 (
Figure 5
)
in this mode. This will allow for a similar recovery of the
emitter circuitry as in normal operation. Pin 1, pin 2, and
pin 12 should be buffered with a unity gain amplifier to
measure their outputs.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33099CEG | Adaptive Alternator Voltage Regulator |
| MCZ33198EF | Automotive High-Side TMOS Driver |
| MCZ33199EF | Automotive ISO 9141 Serial Link Driver |
| MCZ33285EF | Dual High-Side TMOS Driver |
| MCZ33287EG | Contact Monitoring and Dual Low-Side Protected Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ146012EGR2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Low Power CMOS Photoelectric Smoke Detector IC |
| MCZ2010AH | 制造商:TDK 制造商全稱:TDK Electronics 功能描述:Common Mode Filters For high-speed differential signal line |
| MCZ2010AH121 | 功能描述:電磁干擾濾波珠子、扼流圈和陣列 120ohms 25% 2 Line RoHS:否 制造商:AVX 阻抗: 最大直流電流:35 mA 最大直流電阻: 容差: 端接類型:SMD/SMT 電壓額定值:25 V 工作溫度范圍:- 25 C to + 85 C 封裝 / 箱體:0603 (1608 metric) |
| MCZ2010AH121L4T | 制造商:TDK CORPORATION OF AMERICA 功能描述:EMC |
| MCZ2010AH201L4T | 功能描述:共模濾波器/扼流器 200ohms 100mA 5V 4 Line RoHS:否 制造商:TDK 電感: 阻抗:35 Ohms 容差: 最大直流電流:0.1 A 最大直流電阻:1.5 Ohms 自諧振頻率: Q 最小值: 工作溫度范圍:- 25 C to + 85 C 端接類型:SMD/SMT 封裝 / 箱體:0302 (0806 metric) 系列:TCE |
發布緊急采購，3分鐘左右您將得到回復。