- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33884EG (飛思卡爾半導體(中國)有限公司) Switch Monitor Interface PDF資料下載
參數資料
| 型號： | MCZ33884EG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Switch Monitor Interface |
| 中文描述： | 開關顯示器接口 |
| 文件頁數： | 12/21頁 |
| 文件大?。?/td> | 251K |
| 代理商： | MCZ33884EG |
Analog Integrated Circuit Device Data
Freescale Semiconductor
12
33884
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
POWER-UP
On initial power-up all 33884 registers are cleared and the
device enters the Sleep mode. To exit the Sleep mode, a
valid command word is required to be received from the
microprocessor.
SLEEP COMMAND
Sleep mode can be entered by a SPI Sleep command or
asserting the RST pin. In Sleep mode all inputs are Tri–State
and all internal active pull up and pull down currents are
disabled. Sleep mode reduces the current drain to a
quiescent current level of 10
μ
A and disables the IC. Sleep
mode provides lowest quiescent current for the IC. Exit from
sleep mode requires a valid SPI RUN, TRI–STATE, or
METALLIC command.
RUN COMMAND
The Run command places the IC in one of three operating
modes:
1. This is the normal operating mode
of the 33884. In
Normal mode the status of the input switches are
latched on falling edge of CS and data is returned to
the MCU via SPI. All programmed combinations of
source and sink currents, used for sensing purposes,
are always active in this mode. While in the Normal
mode, an interrupt is generated and sent to the
microprocessor whenever an external switch changes
its OPEN or CLOSED state. Prior to a switch closing,
the 33884 sources 0.75 mA of sustain current. When
the voltage at the input crosses the comparator
threshold, 14 mA of current is allowed to flow. The 14
mA wetting current shuts off after a 20 ms timer
expires.
2. The Polling mode
reads a switch status periodically,
interrupting the microprocessor only when an external
switch is sensed as being CLOSED. When the 33884
senses all external switches to be OPEN, the Polling
mode of operation continues. When a switch is sensed
CLOSED, an interrupt is sent to the microprocessor,
transferring it’s operational mode to the Normal mode.
The Polling mode provides a reduction in quiescent
current by turning OFF all source and sink currents
during sensed switch OFF periods. The Polling mode
allows reduction of quiescent current by disabling sink
and source currents during switch OFF periods.
3. The Polling + INT Timer mode
of operation is similar to
the Polling mode above, except with the addition of an
interrupt being sent to the microprocessor if a switch is
sensed CLOSED, or upon the internal interrupt timer
timing out
. An interrupt is always ultimately sent to the
microprocessor in this mode. The microprocessor can
be programmed to read, or ignore the reported switch
status while receiving the interrupt. If a switch is
sensed CLOSED, operation automatically reverts to
the Normal mode. If all switches are sensed OPEN,
and the wake up timer (INT Timer) times out, the 33884
continues to operate in the Polling + INT Timer mode.
The wake up timer duration may be set much longer
than the polling time.
The command also programs the SP1 to SP4 sense inputs
(switch-to-battery logic [1] or switch-to-ground logic[0]).
Please refer to
Table 17
.
TRI-STATE COMMAND
A Tri-State command places all switch inputs into Tri-State
position. All comparators on input are disabled in this mode.
The device will return logic [0] for the switch status.
SPI PROGRAMMING
The 33884 uses the SPI in full duplex synchronous slave
mode for communication with the microprocessor. The 33884
is programmed via a 16-bit word command from the MCU.
The word is sent to the device with the MSB first. The
command word sent to the 33884 sets the mode of operation
in the device. Returning data received from the 33884 is the
status of the sensed input switch on the falling edge of CS.
Sixteen clock periods are required for each transmission to
be valid. After the 16 clocks, CS is returned to the inactive
state (logic [1]), command words are no longer accepted into
SI, and the SO pin is Tri-Stated. The response to a SPI
command returns status based on previous command word.
This previous command could be a hardware reset as well as
any of the other commands discussed in this section.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33887EK | 5.0 A H-Bridge with Load Current Feedback |
| MCZ33889BEG | System Basis Chip with Low Speed Fault Tolerant CAN Interface |
| MCZ33927EK | Transistor; Type: Amplifiers/Bipolar; VCEO (V): -100; Ic (A): -1; Pc (W): 0.9; hFE: 140 to 350; VCE (sat) (V) max: -0.5; Package: TO-92Mod |
| MCZ33970EG | Dual Gauge Driver Integrated Circuit with Improved Damping Algorithms |
| MCZ33976EG | Dual Gauge Driver with Configurable esponse Time |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33884EG | 制造商:Freescale Semiconductor 功能描述:SWITCH MONITOR INTERFACE 24SOIC |
| MCZ33884EGR2 | 功能描述:多路器開關 IC SW DETECT INTERFACE RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MCZ33887EK | 功能描述:馬達/運動/點火控制器和驅動器 H-BRIDGE W/LD CUR FDBK RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33887EKR2 | 功能描述:馬達/運動/點火控制器和驅動器 H-BRIDGE W/LD CUR FDBK RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33887EKR2DH | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:5.0 A H-Bridge with Load Current Feedback |
發布緊急采購，3分鐘左右您將得到回復。