參數資料
型號： MD83C154DXXX-12/883
廠商： TEMIC SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CDIP40
文件頁數： 5/28頁
文件大小： 6193K
代理商： MD83C154DXXX-12/883
13
2467X–AVR–06/11
ATmega128
Stack Pointer
The Stack is mainly used for storing temporary data, for storing local variables and for storing
return addresses after interrupts and subroutine calls. The Stack Pointer Register always points
to the top of the Stack. Note that the Stack is implemented as growing from higher memory loca-
tions to lower memory locations. This implies that a Stack PUSH command decreases the Stack
Pointer.
The Stack Pointer points to the data SRAM stack area where the Subroutine and Interrupt
Stacks are located. This Stack space in the data SRAM must be defined by the program before
any subroutine calls are executed or interrupts are enabled. The Stack Pointer must be set to
point above $60. The Stack Pointer is decremented by one when data is pushed onto the Stack
with the PUSH instruction, and it is decremented by two when the return address is pushed onto
the Stack with subroutine call or interrupt. The Stack Pointer is incremented by one when data is
popped from the Stack with the POP instruction, and it is incremented by two when data is
popped from the Stack with return from subroutine RET or return from interrupt RETI.
The AVR Stack Pointer is implemented as two 8-bit registers in the I/O space. The number of
bits actually used is implementation dependent. Note that the data space in some implementa-
tions of the AVR architecture is so small that only SPL is needed. In this case, the SPH Register
will not be present.
RAM Page Z Select
Register – RAMPZ
Bits 7..1 – Res: Reserved Bits
These are reserved bits and will always read as zero. When writing to this address location,
write these bits to zero for compatibility with future devices.
Bit 0 – RAMPZ0: Extended RAM Page Z-pointer
The RAMPZ Register is normally used to select which 64K RAM Page is accessed by the Z-
pointer. As the ATmega128 does not support more than 64K of SRAM memory, this register is
used only to select which page in the program memory is accessed when the ELPM/SPM
instruction is used. The different settings of the RAMPZ0 bit have the following effects:
Note that LPM is not affected by the RAMPZ setting.
Instruction
Execution Timing
This section describes the general access timing concepts for instruction execution. The AVR
CPU is driven by the CPU clock clk
CPU, directly generated from the selected clock source for the
chip. No internal clock division is used.
Bit
151413
1211
10
9
8
SP15
SP14
SP13
SP12
SP11
SP10
SP9
SP8
SPH
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0
SPL
765
432
10
Read/Write
R/W
Initial Value
0
000
00
Bit
7
6
543
2
1
0
–
––
–
RAMPZ0
RAMPZ
Read/Write
R
R/W
Initial Value
0
RAMPZ0 = 0:
Program memory address $0000 - $7FFF (lower 64 Kbytes) is
accessed by ELPM/SPM
RAMPZ0 = 1:
Program memory address $8000 - $FFFF (higher 64 Kbytes) is
accessed by ELPM/SPM
相關PDF資料
PDF描述
MF280C51-30D 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQFP44
MR80C32E-16P883 8-BIT, 16 MHz, MICROCONTROLLER, CQCC44
MR80C32E-16P883 8-BIT, 16 MHz, MICROCONTROLLER, CQCC44
MQ83C154DCXXX-25P883D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44
MR80C52EXXX-25:RD 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44
相關代理商/技術參數
參數描述
MD83C154-L16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MD83C154T-12 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MD83C154T-16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MD83C154T-20 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MD83C154T-25 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*