參數資料
型號： MDEV-LICAL-MS
廠商： Linx Technologies Inc
文件頁數： 9/24頁
文件大小： 0K
描述： DEV SYSTEM MS SERIES 418MHZ
軟件下載： MS Series Master Dev Software
標準包裝： 1
系列： MS
類型： 編碼器，解碼器
適用于相關產品： MS 系列編碼器和解碼器
已供物品： 2 個板，2 個編碼器，2 個解碼器，2 根天線
其它名稱： MDEV-LIC-MS
MDEV-LIC-MS-ND
–
13
the line to ground while trying to power down the receiver. This mode is
appropriate for receivers that have a high internal pull-up resistance, such
as those offered by Linx. If the intended receiver does not have a pull-up,
then a 100k
Ω or larger resistor to V
CC can be added to the RX_CNTL line to
activate this mode.
TX ID
The TX_ID line will output an eight-bit binary number to identify which
learned encoder sent the transmission. The number is output at the baud
rate set by the SEL_BAUD lines and will normally correspond to the order in
which the decoder learned the encoder, so the first encoder learned will get
number ‘1’, the second will get number ‘2’, and so on. An exception arises
when the memory is full, in which case the first numbers are overwritten as
described in the Learn Mode section. Application Note AN-00156 shows
some example software to read the TX_ID and associate it with a particular
encoder. The C and Visual Basic code is well documented so that it can be
modified for a specific application.
System Example
The first step in using the decoder is to set the baud rate and determine if
the outputs should be latched or momentary. Next, the decoder will need
to learn the encoder’s Code Word. This is done by momentarily pressing
the button connected to the LEARN line. The LED connected to the
MODE_IND line will begin to flash to indicate that the decoder is ready to
learn a new Code Word. One of the buttons on the transmitter is pressed
to send a signal to the decoder. Once this is done, the LEARN button is
pressed again to exit Learn Mode.
Now, when a button is pressed on the encoder, the corresponding line on
the decoder will activate. If the LATCH line is high, the data line will remain
high until the encoder button is pressed again, telling the decoder to pull
the line low.
To clear the memory of the decoder, the LEARN button is pressed and
held for ten seconds, until the LED turns off. Once the button is released,
the LED will light for two seconds to indicate that the memory has been
cleared.
相關PDF資料
PDF描述
MAX2622EVKIT EVAL KIT
MAX2751EVKIT EVAL KIT
MAX2750EVKIT EVAL KIT
MAX2663EVKIT EVAL KIT
MAX2605EVKIT EVAL KIT
相關代理商/技術參數
參數描述
MDEV-LICAL-MS-ES 功能描述:其他開發工具 MS Series Master Dev Kit w/ ES RF Modules RoHS:否 制造商:Parallax 產品:ELEV-8 Hex Upgrade Kits 類型:Robotics 工具用于評估:ELEV-8 Quadcopter 工作電源電壓:
MDEV-LICAL-MT 功能描述:其他開發工具 MT Series Master Dev Kit RoHS:否 制造商:Parallax 產品:ELEV-8 Hex Upgrade Kits 類型:Robotics 工具用于評估:ELEV-8 Quadcopter 工作電源電壓:
MDEV-USB-QS 功能描述:界面開發工具 QS Master Dev Sys RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
MDF005 制造商:MIC 制造商全稱:MIC GROUP RECTIFIERS 功能描述:SURFACE MOUNT BRIDGE
MDF01 制造商:MIC 制造商全稱:MIC GROUP RECTIFIERS 功能描述:SURFACE MOUNT BRIDGE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*